The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (Sf) is equal to 0.8 Su and endurance Strength (Se) is equal to 0,5 Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S-N diagram

The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (Sf) is equal to 0.8 Su and endurance Strength (Se) is equal to 0,5 Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S-N diagram

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

A solid shaft is subjected to a twisting moment of 150 kNm. If the angle of twist is 8º per meter of the shaft and the shear stress is not to exceed 550 MPa. Determine the suitable shaft diameter by comparing the strength design and rigidity design. Also, determine the maximum shear strain acting on the shaft. Take G 250 GPa. Diameter of shaft based on Strength design is in mm Diameter of shaft based on rigidity design is in mm The sutable Diameter of the shaft is in mm The maximum shear strain is
The armature shaft of a 50 kW, 580 rpm electric motor, mounted on two bearings A and B, is shown in Fig. The total magnetic pull on the armature is 5 kN and it can be assumed to be uniformly distributed over a length of 400 mm midway between the bearings. The shaft is made of steel with an ultimate tensile strength of 770 N/mm2 and yield strength of 580 N/mm2. Determine the shaft diameter using the ASME code if, kb=1.5 and kt=1.0 Assume that the pulley is keyed to the shaft.
An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter of an input shaft is d = 20 mm and its material is 16MnCr5. A force of F = 2800 N forces the shaft due to the operation of a gear wheel connected with a wedge on the input shaft. The distances of the gear from the bearings are given as L₁ = 40 mm and L2 = 60 mm. In the most dangerous section, you are required to check the strength according to the S = 3 safety factor. If the section is unsafe in terms of strength, what changes would you make in the design to make it safe? (The surface of the spindle is machined as fine chips, reliability poor Kg = 1.).
A loading condition of a curved beam is shown below. It is made from a steel with a yield strength (Sy) of 400 MPa. a) Determine the critical location. b) If the safety factor against yielding (n) at the critical location is 2.5, using maximum shear stress theory or distortion energy theory, determine the allowable load P.
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength ( Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (S) is equal to 0.8Su and endurance Strength (Se) is equal to 0, 5Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S - N diagram
a) The factors of safety predicted at point H by the maximum shear stress theory of failure (Tresca criterion) i) The second moment of area relative to z-axis, I_z, for the cross-section can be calculated as ( Enter your answer in cm4 ii) The bending stress at Point H can be calculated as (Enter your answer in MPa, Compressive stress is negative and tensile stress is positive) iii) The first moment of area required to calculate shear stress at H can be calculated as (Enter your answer in mm^3) iv) The absolute value of the transverse shear stress at point H can be calculated as (Enter your answer in MPa ) v) Maximum principal stress can be calculated as (Enter your answer in MPa ) vi) Minimum principal stress can be calculated as (Enter your answer in MPa ) vii) The equivalent stress for Maximum-Shear-Stress Theory ( Tresca criterion) (Enter your answer in MPa ) b) The von Mises equivalent stresses at point H can be calculated as: MPa c) The factors of safety at point H…
A 5 in steel shaft is to be replaced with a hollow shaft of the same material and is equal in torsional strength, yet the hollow shaft weighs only 75% of the solid shaft per unit length. Identify the dimension of the hollow shaft
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
You are designing a driveshaft for a motor from a material with G = 15,000 ksi. The specifications for the project require a solid shaft to be used. Based on the location of the motor, the driveshaft has a length L = 9.55 ft. The motor provides 67 hp at a rotation rate of 2475 rpm.Your design requires φ ≤ 0.905° over the length of the shaft. Additionally, the maximum shear stress in the material τmax ≤ 4.0 ksi.Determine rmin, the minimum radius
A shaft is designed to transmit power of 100 kW at 180 rpm. The allowable shear stress is 50MPa and modulus of rigidity of 80 GPa. The angle of twist is not to exceed to 1° in 4-meter length A. Calculate the diameter of the shaft in inches. B.If the shaft in A is to be fitted to a hub with material SAE 0105 and fit classification of FN3, what will be the maximum and minimum stresses based on the interference of metal.
Design of a Shaft subjected to Alternating Loads 1. [Proof of Concept] Considéra machined steel circular shaft subjected to maximum and minimum bending moment of 1000 and 4000 lb .in, respectively; and a maximum and minimum torque of 250 and 1600 Ib.in, respectively. Consider the factor of safety to be 2, the yield strength of the materials 40 ksi, and its ultimate strength to be 70ksi.Determine the minimum diameter of the shaft for the case where D is 20% larger than d, the fillet radius is 10% of d, and reliability is 99%. You may use DE-ASM E formula. 2. Write a computer code that can take Tm, Ta, Mm, Ma, choice of material, safety factor, and other necessary assumptions from the user and return an estimated diameter for the shaft.Choice of inputs is up to you. Note that many of the required quantities are themselves function of the shaft diameter. Your code should be submitted with a report.
helical spring is to support a load of 10 kN. The spring is guided by a rod of 40 mm diameter. The spring undergoes a deflection of 40 mm under the load. Determine the diameter of the wire and the number of turns required. Use steel with a factor of safety 3.