5-4 Composite A-36 steel bar shown made from two segments AB and BD. Area AAB = 600 mm2 and ABD = 1200 mm². Determine the vertical displacement of end A and displacement of B relative to C. A 75 kN 20 kN 40 KN D 20 KN Im 0.75 m 40 KN 0.5 m (Hibberler, 2011)

5-4 Composite A-36 steel bar shown made from two segments AB and BD. Area AAB = 600 mm2 and ABD = 1200 mm². Determine the vertical displacement of end A and displacement of B relative to C. A 75 kN 20 kN 40 KN D 20 KN Im 0.75 m 40 KN 0.5 m (Hibberler, 2011)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.7P: -7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the...

See similar textbooks

Related questions

Q: enturimeter of 0.5 contraction ratio has been fixed in a 100 mm diameter horizontal pipe.The head of…

A: Given:d=100 mmcontraction ratio=0.5No flow pressure head=P1ρg=3 m +10.3 m=13.3 mthroat pressure…

Q: A column has a rectangular cross-section of 10mm x 20mm and a length of 1m. The slenderness ratio of…

A: Ratio of length of the column and the radius of gyration of the column is known as slenderness…

Q: A two-dimensional fluid element rotates like a rigid body. At a point within the element, the…

A: Given:2-D fluid element,Pressure=1 unit,Find,radius of the mohr's circle?

Q: The atmospheric pressure at the sea-level is 101.3 kN/m² and the temperature is 15°C. Calculate the…

Q: a) How much energy does it take to accelerate a vehicle of mass 4390 kg from stationary to 38 m/s?…

Q: A vapour compression refrigeration plant using R12 has saturation temperatures in the evaporator and…

Q: The pins at C and A are in double shear, and the pin at B is in single shear. All pins have a…

Q: In a power plant operating with water and steam, the following measurements and observations were…

Q: A force of magnitude P= 176 N is applied to the stationary machine handle as shown. Write the force…

Q: Find the total pressure on a circular plate of diameter 1.5 m which is placed vertically in water in…

A: Given:Diameter of plate=1.5 md=1.5 mDistance between centre of plate and free water surface=3 mh¯=3…

Q: Question Two ( A three stage C.P. has impellers (Pcm) in diameter and (1.8cm) wide at outlet. The…

A: A three stage C.P. No of stage = 3 Diameter of outlet D2= 40 cm =0.4 m Width pof outlet B2 = 0.018m…

Q: The heat flux that is applied to the left face of a plane wall is q" = 50 W/m². The wall is of…

Q: Problems 1.85 through 1.92 refer to a linkage that is to act as a crank-rocker mechanism Link…

Q: Determine the minimum weight W to prevent downplane motion of the 1000 lb body. The coefficient of…

Q: 19) Tick mark the correct statement: (a) Centrifugal pump convert mechanical energy into hydraulic…

A: This question is based on the concept of centrifugal pump and reciprocating pump.

Q: 20) Indicator diagram shows for one complete revolution of crank the: (a) variation of kinetic head…

Q: Determine the area moments of inertial and ly. Given that c = 0.94 in. 4 in. y 0.5 in. -0.5 in. 4…

A: From the given figure: The radius of curvature →c=0.94 in So the moment of inertia about X axis:…

Q: # Find the shortest length of duminium tubes 50mm outer diameter x 45 mm inner diameter with minimum…

Q: 10 hot rods (L = 5 m and d = 2 cm) are buried in the ground parallel to each other each rod is 10 cm…

A: The given information in the problem is shown in the following attached image:

Q: Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear…

A: Plotting stress-strain graph from the given data in table:

Q: 1 The pole is subjected to the forc F which has components F, = 1.3 kN and F, =1.45 kN. If 8-71",…

A: Given forces in x and z direction. Required- F and Fy.

Q: The horizontal roof of a building has an emittance of 0.9. Air temperature is 1oC on a clear night.…

A: In this problem, we will calculate the temperature of the roof by using the energy balance. For the…

Q: 3.12 (USCS Units) A low-carbon steel tensile specimen with starting gage length = 2.0 in and…

Q: 1. Air at 1450 kPaabs and 100°C flows in a 20-mm- diameter tube. What is the maximum laminar flow…

Q: P Tav P σαν

A: GivenA=0.024 mθ=40oσav=200kPaP=8.18 kNτav=-168 kPa

Q: R₁ $D₁ P = 20 kN = Mv 600 Nm. $D₂ R₂ D3 *** D₁ = 34 mm, D₂ = 40 mm, D3 = 36 mm, R₁ = 5 mm, R₂ = 2…

A: Draw the shear force diagram P=20 kN, MV=600N.m

Q: 13. There are 1.5 Kgm of a gas where K = 1.3 and R = 0.38- K] Kom-K that undergo an isochoric…

A: To find: The heat transferred, the change in internal energy, and the change in entropy. Given: The…

Q: Problem 12.145 - Enhanced with Hints and Feedback Particles A and B are traveling counterclockwise…

A: Given the speed of both cyclists, radius and tangential acceleration. Required: Distance between…

Q: 11.93 Engineers are examining how shock absorber designs affect the displacement of a mountain…

A: For the solution refer below images.

Q: In Eigure 1), F-900 lb. Fy=400 lb, and F-900 lb. Figure 1 of 1 Part A Determine the magnitude of the…

Q: vertical, frictionless piston-and-cylinder arrangement contains 1 kg of steam at 25 bar, 260°C.…

A: Given:m=1 kgP=25 bar T=260o Cg=9.145 m/s2

Q: Problem I: Consider a 10 cm x 15 cm x 2.5 m Aracan timber beam. Its specific gravity is 0.65.…

Q: Data has been gathered from a lifting system used to transport engine parts. The system consists of…

A: Using the second equation of motion, we will compute the linear velocity, linear acceleration,…

Q: why is there no translational part for the kinetic energy here?

A: Given: There is welded two rods AB and BC so Both the rods have same angular speed at the same…

Q: 2. Consider the following compound pendulum, which consists of a thin rod attached to a pivot point…

A: For solution refer below images.

Q: 400 lb A ss Te B Part A Determine the design angle (0°<< 90°) for strut AB so that the 400 lb…

A: Given data:- Force acting at A= 400 lb ϕ=39 Force component along AC=505 lb To find:- angle θ the…

Q: II. Photovoltaics' Problem For a photon with a wavelength of 832 nm (green light), calculate: a) the…

Q: FBD 3. Determine the required thickness of member BC and the diameter of the pins at A and B if the…

A: Given data Failure normal stress = 30ksi Failure shear stress = 12 ksi Factor of safety = 1.2 Find…

Q: Q₁) In an ideal otto cycle engine, the temperature and Pressure at the beginning of Compression are…

A: In this problem, we will determine the Otto cycle compression ratio, air standard efficiency, and…

Q: A copper pipe carrying hot water is losing heat with a convective heat transfer coefficient of h =…

Q: A Carnot refrigerator has working temperatures of -30°C and 35°C. If it operates with Refrigerant…

A: The answer is given below,

Q: Problem 3: Inputs: a = 12 in b = 12.75 in Table not requ Use the scalar approach (not the cross…

Q: A beam with hinge supports on both ends has __________ redundant support a. one b. two c. three d.…

Q: Determine area about the y-axis. the moment of inertia of the shaded

A: According to the given data we need to find The moment of inertia about the y-axis

Q: Cable ABCD support. Determine the maximum tension in this cable 1m ya B 4 kN -3 m 2m C 0.5 m 6 kN D

Q: Cite the indices of the direction that results from the intersection of (1 10) and 1) in a cubic…

Q: Given the horizontal beam AB with two supports Pin A and Roller B. The system is subjected to…

Q: For the beam illustrated in the figure, find the locations and magnitudes of the maximum tensile…

A: The given information in the problem is shown in the following attached image:

Q: one pound of air R=(53.3 ft-lbf/lbm-degree Rankine) is compress isothermally in a close system from…

A: Isothermic compresion R= 53.3 ft-lbflbm-°R P1 = 15 Psia & T1 = 80 0F P2= 90 Psia To find…

Q: Determine the magnitude of the resultant internal normal force, shear force and bending moment on…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

แสดงวิธีทำให้ดูหน่อย

5-4 Composite A-36 steel bar shown made from two segments AB and BD. Area
AAB = 600 mm2 and ABD = 1200 mm². Determine the vertical displacement of end A and
displacement of B relative to C.
วิธีทํา
20 KN
B
75 KN
40 KN
20 KN
Im
0.75 m
40 KN
0.5 m
(Hibberler, 2011)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Final solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the weight density of steel.
, Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14 kN/m, and L = L2 m.
.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A mountain bike rider going uphill applies a force P = 65 N to each end of the handlebars AB CD, made of aluminum alloy 7075-T6, by pulling on the handlebar extenders (DF on right handlebar segment). Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A), Segments AB and CD are prismatic with lengths Lvand L3 and with outer diameters and thicknesses J01, /01 and d03, /03, respectively, as shown. Segment BC of length L2, however, is tapered, and outer diameter and thickness vary linearly between dimensions at B and C Consider shear, torsion, and bending effects only for segment AD; assume DFis rigid. Find the maximum tensile, compressive, and shear stresses adjacent to support A. Show where each maximum stress value occurs
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
A thin metal strip of total weight W and length L is placed across the top of a flat table of width L2as shown in the figure. What is the clearance S between the strip and the middle of the table? (The strip of metal has flexural rigidity EI.)
A statically indeterminate stepped shaft ACE is fixed at ends A and B and loaded by a torque TQat point C (see figure). The two segments of the bar are made of the same material, have lengths L4and LB, and have polar moments of inertia IAand Ipb. Determine the angle of rotation 4>of the cross section at Cby using strain energy. Hint: Use Eq, (3-55b) to determine the strain energy Urn terms of the angle d?. Then equate the strain energy to the work done by the torque to. Compare your result with Eq. (3-52) of Example 3-9.
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Repeat Problem 9,5-15 for the anti-symmetric loading shown in the figure.
Solve Problem 11.3-3 for a W 10 × 45 steel column having a length L = 28 ft.
A retaining wall (Fig. a) is constructed using steel W-shape columns and concrete panel infill (Fig, b). Each column is subjected to lateral soil pressure with peak intensity q0(Figs, b and c). The tensile and compressive strength of the beam is 600 MPa. Select the most economical W 360 section from Table F-l(b) based on safety factor of 3.0.