5-41. The bulk head AD is subjected to both water and soil-backfill pressures. Assuming AD is "pinned" to the ground at A, determine the horizontal and vertical reactions there and also the required tension in the ground anchor BC necessary for equilibrium. The bulk head has a mass of 800 kg. D B C F 181 0.5 m

5-41. The bulk head AD is subjected to both water and soil-backfill pressures. Assuming AD is "pinned" to the ground at A, determine the horizontal and vertical reactions there and also the required tension in the ground anchor BC necessary for equilibrium. The bulk head has a mass of 800 kg. D B C F 181 0.5 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.50P

See similar textbooks

Similar questions

the cylinder with a mass of 1000 Kg is supported as shown in the figure, determine the reaction at the hinge.
The bulk head AD is subjected to both water and soil-backfill pressures. Assuming AD is “pinned” to the ground at A, determine the horizontal and vertical reactions there and also the required force F in the ground anchor BC necessary for equilibrium. The bulk head has a mass of 4800 kg.
If the weight of the h0m0gen0us cylinder in equilibrium is 750N, what is the magnitude (N) of the n0rmal f0rce if the surface is r0ugh?
The A-36 steel wires AB and AD each have a diameter of 2 mm and the unloaded lengths of each wire are LAC = 1.60 m and LAB = LAD = 2.00 m. Determine the required diameter of wire AC so that each wire is subjectedto the same force when the 150-kg mass is suspended from the ring at A.
The shaft-pulley assembly is supported by the universal joint at O and by the slider hearing at A. The pulley, which has a mass of 7 kg, is subjected to the belt tensions shown. The mass of the shaft may be neglected. Draw an FBD that consists of the pulley and shaft AO. Determine the number of unknowns on this FBD.
The pulley system is used to lift a weight of 1.088 N. Determine the force P needed to bring the system into equilibrium.
The cylinder having a diameter 2.5 ft weighs 57 lb and is 6 ft long. Determine the reaction (lb.) at A neglecting friction. Determine the reaction at B (lb.) neglecting friction. Weight density of water is 62.4 lb/ft3 Sp.gr Gs = 1.6
Draw the free body diagram and determine all the reation
Don't copy from other websites solution. The wall crane supports a load of 660lb. The jib ABC has a weight of 152lb and member BD has a weight of 38lb. Each member is uniform and has a center of gtravity at its center. A)Determine the horizontal component of reaction at the pin A. B)Determine the vertical component of reaction at the pin A. C)Determine the horizontal component of reaction at the pin D. D)Determine the vertical component of reaction at the pin D. E)What is the force in the cable at the winch W?
The jib crane is supported by a pin at C and rod AB. If the load has a mass of 1.89 Mg with its center of mass located at G. If x = 5 m, determine the following: 9.1 The force developed in rod AB on the crane is Blank 1 kN. 9.2 The support reaction at pin C is Blank 2 kN. 9.3 The jib crane is supported by a pin at C and rod AB. The rod can withstand a maximum tension of 38 kN. If the load has a mass of 2 Mg, with its center of mass located at G, determine the maximum allowable distance x in meters.
If d=2m and F-200N and the mass of ball 30 kg Determine the forces in cables AC and AB in equilibrium 1.5 m F -2 m- Maximum size for new files: 128MB
A spring with a torsional stiffness k is attached to the hinge at B. It is unstretched when the rod assembly is in the vertical position. Determine the weight W of the block that results in neutral equilibrium. Hint: Establish thepotential energy function for a small angle θ, i.e., approximate sin θ ≈ 0, and cos θ ≈ 1 - θ2/2.