A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile load of 27,500 N. It must not experience either plastic deformation or a diameter reduction of more than 7.5 x 10³ mm. Of the materials listed as follows, which are possible candidates? Justify your choice(s).

A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile load of 27,500 N. It must not experience either plastic deformation or a diameter reduction of more than 7.5 x 10³ mm. Of the materials listed as follows, which are possible candidates? Justify your choice(s).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As a material scientist, you have been requested by an engineer to list down a possiblecylindrical rod alloy to be used in your next project. Each cylindrical rod having adimension of 100 mm long and a diameter of 10.0 mm is to be deformed using a tensileload of 27,500 N. It must not experience either plastic deformation or a diameterreduction of more than 7.5 × 10−3 mm. Based on materials listed in Table 2, which arepossible candidates? Justify your choice(s).
A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of 30,000 N. The rod is to experience an elongation not more than 1.3 mm and FOS ≥ 1.5 setting yield strength as a criteria. Additional constraints to be met are max specific stiffness and %EL not more than 0.15. Which of the below listed materials are possible candidates? Justify your choice(s) by making a table of constraints. Materials Modulus of Elasticity, (GPa) Yield Strength, (MPa) Tensile Strength, (MPa) Aluminum alloy 70 300 450 Titanium alloy 107 400 550 Steel alloy 207 500 750
A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of 30,000 N. The rod is to experience an elongation not more than 1.3 mm and FOS ≥ 1.5 setting yield strength as a criteria. Additional constraints to be met are max specific stiffness and %EL not more than 0.15. Which of the below listed materials are possible candidates? Justify your choice(s) by making a table of constraints.
What is the maximum value of KIc as per LEFM that can be determined from experiments on a 20 mm thick plate? yield strength= 500 MPa, E= 210 GPa, poission ratio=0.3.
Both yield strength and ultimate tensile strength exhibit the ability of a material to withstand a certain level of load. Which parameter do you prefer to use as a design parameter for a proper selection of materials for structural applications? Explain
Describe the behavior of tested materials (mild steel and aluminium) as it responds to increasing load, in tensile test experiment.
The stress element corresponds to a point under a flat stress state, on the surface of a part made with a material that has a yield limit of 700 MPa. What is the safety coefficient against runoff, according to the criteria of Von Mises and Tresca?
1) a) How can we test which can withstandthe most stress, a length of spider web thread or a steel wire of the same length? b) Explain, the differences between a ductile and a brittle material. d) Describe some of the connections between Hooke's Law, Young's Modulus and the tensile properties of materials. e) Explain why alloying makes metals harder. f) Describe the differences between an amorphous and a crystalline material.
You are in charge of a project to design novel materials to replace the following;i) hip boneii) LumbardiscUsing a suitable stress-strain curve, describe the mechanical properties of the newmaterials i.e titanium alloy, polythylene and cobalt
Define the term Modulus of Toughness?
Using a stress-strain diagram, analyze and compare the mechanical properties of cast iron, mild steel and glass materials
Based upon the percent elongation of a tensile sample, A ductile engineering materials to find by value equal to or greater than 5% and a brutal materials defined by a value less than 5% true or false?