5-54. The skid-steer loader has a mass of 1.18 Mg, and in the position showa the center of mass is at Gj. If there is a 300-kg stone in the bucket, with center of mass at Gz, determine the reactions of each pair of wheels A and B on the ground and the force in the hydraulic cylinder CD and at the pin E. There is a similar linkage on each side of the loader. 1.25 m 05 m 0.15 m 1.5 m 0.75 m

5-54. The skid-steer loader has a mass of 1.18 Mg, and in the position showa the center of mass is at Gj. If there is a 300-kg stone in the bucket, with center of mass at Gz, determine the reactions of each pair of wheels A and B on the ground and the force in the hydraulic cylinder CD and at the pin E. There is a similar linkage on each side of the loader. 1.25 m 05 m 0.15 m 1.5 m 0.75 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.9P: The four-bar linkage supports the homogeneous box of weight W. Neglecting the weight of the linkage,...

See similar textbooks

Similar questions

The three A-36 steel wires each have a diameter of 2 mm and unloaded lengths of LAC = 1.60 m and LAB = LAD = 2.00 m. Determine the force in each wire after the 150-kg mass is suspended from the ring at A.
The uniform rod AB has a mass of 75 kg . There is a smooth collar at A. A) Determine the force in the cable when the rod is in the position shown. TBC = ?
5-31. If the force of the smooth roller at B on the bar bender is required to be 1.5 kip, determine the horizontal and vertical components of reaction at pin A and the required magnitude of force F applied to the handle.
The smooth disks D and E have a weight of 220 lb and 100 lb, respectively. If a horizontal force of P = 220 lb is applied to the center of disk E, determine the normal reactions at the points of contact with the ground at A, B, and C.
Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power of pulley A is transmitted to pulley B. Determine the horizontal tension T in the belt on pulley B and the x, y, z components ofreaction at the journal bearing C and thrust bearing D if θ = 45°. The bearings are in proper alignment and exert only force reactions on the shaft.
The pumping unit is used to recover oil. When the walking beam ABC is horizontal, the forceacting in the wireline at the well head is 250 lb. Determine the torque M which must beexerted by the motor in order to overcome this load. The horse-head C weighs 60 lb andhas a center of gravity at Gc. The walking beam ABC has a weight of 130 lb and a centerof gravity at GB, and the counterweight has a weight of 200 lb and a center of gravity atGW. The pitman, AD, is pin connected at its ends and has negligible weight.
Find the minimum force P required for impending motion of the block up the inclined surface, given: Mblock = 65 kg, θ = 52 °, μ = 0.4
The cantilevered jib crane is used to support the load of 780 lb. If the trolley T can be placed anywhere between 1.5 ft ≤ x ≤ 7.5 ft, determine the maximummagnitude of reaction at the supports A and B. Note that the supports are collars that allow the crane to rotate freely about the vertical axis. The collar at B supports a force in the vertical direction, whereas the one at A does not.
The drop gate at the end of the trailer has a mass of 1000 kg and mass center at G. If it is supported by the cable AB and hinge at C. determine the tension in the cable when the truck begins to accelerate at 5 m/s2 to the left.
5-13. Determine the horizontal and vertical comp nents of reaction at C and the tension in the cable AB t the truss 30 2 m V3 kN V4 kN 2 m 2 m 2 m
The disk B has a mass of 20 kg and is supported on the smooth cylindrical surface by a spring with stiffness k= 400 N/m and unstretched length l0= 1 m. The spring remains in the horizontal position since its end A is attached to the small roller guide which has negligible weight. Determine the equilibrium angle of the roller.
The A-36 steel wires AB and AD each have a diameter of 2 mm and the unloaded lengths of each wire are LAC = 1.60 m and LAB = LAD = 2.00 m. Determine the required diameter of wire AC so that each wire is subjectedto the same force when the 150-kg mass is suspended from the ring at A.