5-91. The A992 steel shaft is made from two segments. AC has a diameter of 0.5 in. and CB has a diameter of 1 in. If the shaft is fixed at its ends A and B and subjected to a uniform distributed torque of 60 lb.in./in. along segment CB, determine the absolute maximum shear stress in the shaft. 5 in. 0.5 in. 20 in. Prob. 5-91 60 lb-in./in. 1 in.

5-91. The A992 steel shaft is made from two segments. AC has a diameter of 0.5 in. and CB has a diameter of 1 in. If the shaft is fixed at its ends A and B and subjected to a uniform distributed torque of 60 lb.in./in. along segment CB, determine the absolute maximum shear stress in the shaft. 5 in. 0.5 in. 20 in. Prob. 5-91 60 lb-in./in. 1 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The circular steel shaft is subjected to two torques as shown. The segment AB is hollow, with outside diameter of 1 inch and an inside diameter of ½ inch. The segment BC is solid, with a diameter of 1 inch. Determine (a) the maximum shear stress in the shaft, and (b) the angle of twist in degrees between A and C, using G = 12 x 10⁰ psi. 750-in. Ⓡ 2 ft 2000-in. 18 Itin. 3 ft Lin.
5-83 The A-36 steel shaft is made from two segments: AC has a diameter of 0.5 in. and CB has a diameter of 1 in. If the shaft is fixed at its ends A and B and subjected to a uni- form distributed torque of 60 lb in./in. along segment CB, determine the absolute maximum shear stress in the shaft. 5 in. 0.5 in. 20 in. 60 lb-in./in. 1 in. B Prob. 5-83
Q.2// The beam is supported by a pin A and a short link BC. Determine the average shear stress developed in the pins at A, B, and C. All pins are in double shear as shown, and each has a diameter of 18mm. -2m Im-
250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E0=205GP,, Ga=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x10-mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vAD 2. The normal strain in member AD, caD 3. The average stress experienced by pin A, T, 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
Questions a/b c₁ = c₂ = c 5 0.291 10 0.312 20 0.323 40 0.328 200 10 E m 200 10 1. 6.3 kNm torque is applied to a 3m long steel angle with a 200mm x 200mm x 10mm cross section. From tabulated properties for equal angles, the gross cross sectional area of the section is 5090 mm². knowing that G = 77 GPa, determine (a) the maximum shearing stress along line m-m. Provide the answer in MPa with precision n to two decimal points. 2. Determine the angle of twist if 1.7 kNm of torque is applied to the above long angle steel. Provide the answer in Degrees with precision to two decimal points.
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and %3D a= 1.5 m, b= 1m, d=30 mm, h= 8 mm E D 2a A B a
The 106-mm-diameter steel shaft is subjected to the torques shown. T1 = 12 kN-m, T2 = 5 kN-m, T3 = 5 kN-m. Determine the angle of twist (degrees) of the end B. Use L1 = 0.62 m., L2 = 0.57 m., L3 = 0.92 m. Shear modulus = 71 GPa. ROUND OFF TO TWO DECIMAL PLACES. A D T3 L3 В L2 T2 T1
Save Answer The 101-mm-diameter steel shaft is subjected to the torques shown. T1 = 10 kN-m, T2 = 4 kN-m, T3 3 kN-m. Determine the angle of twist (in degrees) of the end B. Use L1 = 0.73 m., L2 D 0.52 m., L3 = 0.70 m. Shear modulus = 72 GPa. Round off to two decimal places. Input the numerical value only. A D T3 L3 L2 T2 L1 T1
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a= 1.75 m, b= 1m, d= 50mm, h= 10mm E D 2а b B b a
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a= 1.5 m, b= 1lm, d=30 mm, h= 8 mm E 2а b а —
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the loadP on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a= 1.5 m, b= 1m, d=30 mm, h= 8 mm E D 2а b P A В b a
Q.2// The beam is supported by a pin A and a short link BC. Determine the average shear stress developed in the pins at A, B, and C. All pins are in double shear as shown, and each has a diameter of 18mm. 7 AN