250 mmADP = 25 kNB3060 CTOP VIEW280 mmMember AD is fabricated by joining two bars (E0=205GP,, Ga=82GPA) and is pinned to plateABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins isT,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC.A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitudeequal to 7.5x10-mm/mm. This also causes Point A to displace only along the horizontalresulting to a shear strain at point A equal to y,=+0.00165rad.Determine the following:1. Poisson's ratio of material used in member AD, vAD2. The normal strain in member AD, caD3. The average stress experienced by pin A, T,4. Factor of Safety of pin A with respect to yielding, FS,A5. Displacement of point D, A,

E=2G(1+μ) GIVEN E=205GPa G=82GPa by formula 205=2X82 (1+μ) μ=1.25-1=.25

E 250 mm P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E=205GPA, G=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5×10-4 mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vAD 2. The normal strain in member AD, cAD 3. The average stress experienced by pin A, T, 4. Factor of Safety of pin A with respect to yielding, FS„A 5. Displacement of point D, A,

E 250 mm P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E=205GPA, G=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5×10-4 mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vAD 2. The normal strain in member AD, cAD 3. The average stress experienced by pin A, T, 4. Factor of Safety of pin A with respect to yielding, FS„A 5. Displacement of point D, A,

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.00 in. and a wall thickness of 0.223 in. is fastened to a solid 1.75-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=18 kips, Q=13 kips, L1=4 ft, L2=6 ft, and L3=6 ft. Determine(a) the stresses in all parts of the axial structure.(b) the deflections of joints B and C.
A steel bracket of solid circular crosssection is subjected to two loads, each of which isP = 4.5 kN at D (see figure). Let the dimension variablebe b = 240 mm.(a) Find the minimum permissible diameter dminof the bracket if the allowable normal stress is110 MPa.(b) Repeat part (a), including the weight ofthe bracket. The weight density of steel is77.0 kN/m3.
b. Calculate "P" in KN considering tension failure on net area Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16.6 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 89.31 MPa and its angle of twist is limited to 5.38˚. Use G = 80.35 GPa for steel and L = 455 mm. Round off the final answer to two decimal places.
line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 200 C under a 50 N pull supported at both ends. During measurement, the ttemperature is 50C and the tape is suspended under a 75 N pull. The line is measured on a 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3 mm2 and the coefficient of linear expansion is 0.000016 m/0C. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance.
e. Calculate "P" in KN considering failure on bearing on block shear Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
The assembly consist of two 10mm diameter red brass C83400 Copper rods AB and CD, a 15mm diameter 304 stainless steel rod EF, and a rigid bar G. The modulus of elasticity for red brass C83400 is 101 GPa for 304 stainless steel 193 GPa. If P= 4.3 kN, determine the horizontal displacement of end F of rod EF
1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
A crank arm consists of a solid segment oflength b1 and diameter d, a segment of length b2, and asegment of length b3, as shown in the figure. Two loads Pact as shown: one parallel to -x and another parallel to-y. Each load P equals 1.2 kN. The crankshaft dimensionsare b1 = 75 mm, b2 =125 mm, and b3 = 35 mm.The diameter of the upper shaft is d = 22 mm.(a) Determine the maximum tensile, compressive,and shear stresses at point A, which is locatedon the surface of the shaft at the z axis.(b) Determine the maximum tensile, compressive,and shear stresses at point B, which is located onthe surface of the shaft at the y axis.
Determine the smallest diameter (mm) that can be used in the clevis shown in the figure below if P = 421 kN. The shearing stress of the bolt is 305 MPa. Final answer should have 2 decimal places.
SHOW COMPLETE SOLUTION. FBD GIVEN REQD AND SOLUTION. A machine component is subjected to the forces and couples shown. The component is to be held in place by a single rivet that can resist a force but not a couple. For P = 60 N, determine the location of the rivet hole if it is to be located (a) from G on line FG, (b) from G on line GH.
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The plate shown is fastened to the fixed member by eight 16-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 80 MPa. If P = 8200 N, what is the maximum and minimum shearing stress developed in the rivet.