5-97 A very large tank contains air at 102 kPa at a location where the atmospheric air is at 100 kPa and 20°C. Now a 2- cm-diameter tap is opened. Determine the maximum flow rate of air through the hole. What would your response be if air is discharged through a 2-m-long. 4-cm-diameter tube with a 2- cm-diameter nozzle? Would you solve the problem the same way if the pressure in the storage tank were 300 kPa?

5-97 A very large tank contains air at 102 kPa at a location where the atmospheric air is at 100 kPa and 20°C. Now a 2- cm-diameter tap is opened. Determine the maximum flow rate of air through the hole. What would your response be if air is discharged through a 2-m-long. 4-cm-diameter tube with a 2- cm-diameter nozzle? Would you solve the problem the same way if the pressure in the storage tank were 300 kPa?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pressurized 2-m-diameter tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to the atmosphere. The water level initially is 3 m above the outlet. The tank air pressure above the water level is maintained at 450 kPa absolute and the atmospheric pressure is 100 kPa. Neglecting frictional effects, determine (a) how long it will take for half of the water in the tank to be discharged and (b) the water level in the tank after 10 s.
The compressed air requirements of a manufacturing facility are met by a 120-hp compressor that draws in air from the outside through an 9-m-long, 22-cm-diameter duct made of thin galvanized iron sheets. The compressor takes in air at a rate of 0.27 m3/s at the outdoor conditions of 15°C and 95 kPa. Disregarding any minor losses, determine the useful power used by the compressor to overcome the frictional losses in this duct.
A very large tank contains air at 102 kPa at a location where the atmospheric air is at 100 kPa and 20°C. Now a 2-cm-diameter tap is opened. Determine the maximum flow rate of air through the hole. What would your response be if air is discharged through a 2-m-long, 4-cm-diameter tube with a 2-cm-diameter nozzle? Would you solve the problem the same way if the pressure in the storage tank were 300 kPa?
The liquid storage tank shown in Fig has two inlet streams with mass flow rates w1 and w2 and an exit stream withflow rate w3. The cylindrical tank is 2.5 m tall and 2 m in diam-eter. The liquid has a density of 800 kg/m. Normal operating procedure is to fill the tank until the liquid level reaches a nom-inal value of 1.75 m using constant flow rates:w1=120 kg/min, w2=100 kg/min, and w3=200 kg/min. At that point, inlet low rate w1 is adjusted so that the level remains constant.However, on this particular day, corrosion of the tank has opened up a hole in the wall at a height of 1 m, producing a leak whose volumetric flow rate q4(m3/min) can be approximated by q4=0.025√h−1 where h is height in meters.(a)If the tank was initially empty, how long did it take for theliquid level to reach the corrosion point?(b)If mass flow rates w1,w2,and w3 are kept constant indefi-nitely, will the tank eventually overflow? Justify your answer.
R-134a enters a compressor as a saturated vapor at 80 kPa and exits at a pressure of 400 kPa. If 44 kJ/kg of work is required and 5 kJ/kg of heat is lost to the surroundings. What is the outlet temperature. Round your answer to the nearest whole number.
The compressor tank that holds 80L of air during compression of pressure of 250kpa and the temperature of 30 degrees. The leakage was experienced during the compression process which resulted in a los of 5g of air, therefore the current air in a tank fill 40L at 500kpa. Determine the temperature of the current air in a tank
A fan delivers 400 m3 /min of air at 1 atm and 21 C when rotating at 600 rpm, with a head of 8 cm WG. If the air temperature rises to 80 C with speed and air flow remains constant, determine the new back pressure in cm of water and the ratio of the new power required to the original power.
Water vapor enters a Lule with an input cross-sectional area of 0.02 m2 at a temperature of 1.8 MPa and 400C. Water vapor passes through the Lule with a flow of 5 kg/s, and in this process there is a heat loss of 2.8 kJ / kg from the Lule. If the pressure at the outlet is 1.4 MPa and the speed is 275 M/s, find the speed at which the water vapor enters the Lule and the temperature at the outlet of the Lule.
Air flows steadily and isentroplcally into an aircraft inlet at a rnass flow rateof 100 kgs·1• At a section where the cross-sectional area is 0.5 m2 , thetemperature and pressure are 200 K and 20 kPa, respectively. Determinethe velocity, pressure and cross-sectional area at a downstream sectionwhere the temperature is 350 K. Sketch the flow passage, and show the ·process on a T-s diagram
The air velocity in the duct of a heating system is to be measured by a Pitot-static probe inserted into the duct parallel to the flow. If the differential height between the water columns connected to the two outlets of the probe is 3.2 cm, determine (a) the flow velocity and (b) the pressure rise at the tip of the probe. The air temperature and pressure in the duct are 45° C and 98 kPa, respectively
A pump increases the water presssure from 8kPa at the inlet to 700 kPa at the outlet. Water enters this pump at 41.51 degrees celsius through a 1.145-cm-diameter opening and exits through a 2.821-cm-diameter opening. Determine the velocity of the water at the outlet in m/s when the mass flow rate through the pump is 1.354kg/s. The specific volume of incoming water is 1.547x10-3m3/kg.
The 64-W fan in an aircraft environmental system is to circulate air through the ducting. An analysis of the flow shows that the fan needs to raise the pressure of air by 47 Pa to maintain flow. The fan is located in a horizontal duct with a circular cross-section whose diameter = 30 cm at both the inlet and the outlet. Determine the highest possible average flow velocity in the duct. Give your answer in m/s. Assume the fan operates steadily and that the changes in kinetic and potential energies across the fan are negligible. Note: I start this one by finding the volumetric flow rate from the work input and the pressure rise. Then I divide that by the cross-sectional area of the duct to get velocity.