Answered: 5 Air at 90°C and 1 atm flows over a…

5 Air at 90°C and 1 atm flows over a flat plate at a velocity of 30 m/s. How thick is the boundary layer at a distance of 2.5 cm from the leading edge of the plate? ir Aowe

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.67P

See similar textbooks

Related questions

Q: Consider laminar boundary layer flow over a flat plate as shown in the figure (top view). Ignoring…

Q: What are the turbulence intensity differences on offshore and onshore?

A: Turbulence intensity differences on offshore and onshore ;

Q: Air at 20oC and 1 atm flows over a flat plate at 35 m/s. The plate is 75 cm long and 100 cm depth…

A: Velocity boundary layer thickness The thickness of the velocity boundary layer is normally defined…

Q: 6. During a winter day, wind at 70 km/h, 5°C, and 1 atm is blowing parallel to a 4-m-high and 15…

Q: What does the friction coefficient represent in flow over a flat plate? How is it related to the…

A: Drag force is a force acting on a body (moving or stationary)which is present in a moving or…

Q: how does drag coefficient vary with the Reynolds number? a) low and moderate Reynolds numbers and at…

A: Fluid mechanics

Q: What is the effective angle of attack ? What is the induced drag ? Show them by drawing a sketch and…

Q: Q2: The velocity profile in a laminar boundary layer on a flat plate is to ba modelled by the cubic…

A: Given, uU=ao+a1y+a2y2+a3y3Boundary conditions,1. y=0, u=02. y=δ, u=U3. y=δ, ∂u∂y=04. y=0, ∂2u∂y2=0

Q: A circular sign has a diameter of 50 cm and is subjected to normal winds up to 150 km/h at 10°C and…

A: The diameter of circular sign, D = 50 cm. Wind velocity, V = 150 km/h. Pressure applied on the…

Q: Air at 250C and 1.0 bar is flowing over a flat plate with a velocity of 8 m/s. Determine: (i) The…

Q: A 5-mm-diameter electrical transmission line is exposed to windy air. Determine the drag force…

A: Given data: The diameter of the electrical transmission line, d = 5 mm. The velocity of wind…

Q: During a winter day, wind at 55 km/h, 5°C, and 1 atm is blowing parallel to a 4-m-high and 10-m-long…

A: Given data velocity of wind 55 km/hr = 15.27 m/sec height of the wall h = 4m length of the wall L =…

Q: distance of 1 m from the leading edge of a flat plate, kept at zero angle of incidence to the flow…

A: Given:x1=1 mx4=4 mδ1=0.1 cm

Q: Dust particles of diameter 0.06 mm and density 1.6 g/cm are unsettled during high winds and rise to…

Q: Еxample 2 During a high Reynolds number experiment, the total drag force acting on a spherical body…

A: The friction drag coefficient of the sphere is CD,friction = 0.0115.

Q: A circular sign has a diameter of 52 cm and is subjected to normal winds up to 160 km/h at 10°C and…

A: Given data as per question Diameter = 52 m Velocity of wind = 160 km /h = 44.4 m/s Temperature = 100…

Q: 2-Air at 30 C over a flat plate at speed of 1.2 m/sec. Calculate the boundary layer thickness at…

Q: Q2) Air at 20°C and 1 atm flows over a flat plate at 35 m/s. The plate is 75 cm long and 100 cm…

A: Given: The temperature of air, T = 20°C The pressure of air, P = 1 atm The velocity of air, v = 35…

Q: Discuss the boundary layer profile that would result for a vertical hot plate, and a vertical cold…

A: Boundary layer of vertical suspended hot plate. Particles of air which contact with plate being hot…

Q: A flat plate ( 1.5 m ) long and ( 1.5 m ) wide is towed in water ( ρ = 1000 kg/m3 and ν=1.31 * 10 -6…

A: Given data:

Q: b) A 4 m long and 2 m wide plate shown in Figure Q1(b) is positioned in seawater flowing at 1.5 m/s…

Q: Consider atmospheric air at 25°C and a velocity of 25 m/s flowing over both surfaces of a 1-m- flat…

Q: A large vertical plate 6.1 m high and 1.22 m wide is maintained at a constant temperature of 57+C…

A: Determine the mean film temperature

Q: What is the effect of streamlining on (a) friction drag and (b) pressure drag? Does the total drag…

A: Effect of streamlining on:

Q: QUESTION 3 A flat plate, manufactured from Perspex, is drawn submerged through 25°C still water at a…

Q: is the drag coefficient 2 or 0.2?

A: Yes from figure we can see that drag coefficient at 80000 is 0.2 not 2

Q: Air is flowing at a speed of 5 m/sec between two parallel flat plates. The air temperature is 20o C…

A: Write the given data with suitable variables. v=5 m/sT∞=20 °CP=1 atmT=90 °Cd=60 cm=0.6 m100 cm1 mb=1…

Q: A 2-m-long, 0.2-m-diameter cylindrical pine log(density =513 kg/m3) is suspended by a crane in the…

A: The related diagram is given as, The density of air is written as, The dynamic viscosity at 5 oC…

Q: Water flows at 20°C with a velocity of 1.1 m/s over a flat plate whose length is 15 cm. The boundary…

A: Give data: The velocity of flow, V = 1.1 m/s. The length of plate, L = 15 cm. The density of water,…

Q: A flat plate ( 1.5 m) long and ( 1.5 m) wide is towed in water ( p 1000 kg/m and v=1.31 * 10 “m² /s)…

Q: Show the boundary layer development along the plate and define the characteristics of boundary layer…

A: Given:

Q: In the laminar flow of air (Pr = 0.7) over a heated plate, if & and 8, denote, respectively, the…

A: Given:Pranddtle number, Pr=0.7δ=hydrodynamic boundary layerδT=Thermal boundary layer

Q: Ql: Explain and sketch the boundary layer over a horizontal flat plate, then write the equations…

A: ◆ In laminar region --> Velocity profile is parabolic. ◆ In turbulent region --> Velocity…

Q: 1) Engine oil at 80°C flows over a 6-m-long flat plate whose temperature is 30°C with a velocity of…

Q: A 0.5 m x 2 m flat plate is towed at 5 m/s on a 2-mm-thick layer of SAE-30 oil at 38°C that…

Q: The turbulent boundary layer can be considered to consist of four regions. Which choice is not one…

A: we know that in boundary layer, turbulent zone comes after transition zone.

Q: (b) A smooth thin plate 10 m long and 1 m wide is placed in an air stream at 3 m/s with its length…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: Q2/Engine oil at 80°C flows over a 6-m-long flat plate whose temperature is 30°C with a velocity of…

Q: Air flows over a l-meter-wide flat plate at a constant velocity of 20 m/s and ambient conditions of…

Q: Calculate the heat transfer from a 60 cm x 60 cm plate on which air flows at 40⁰C and. The plate…

Q: A fluid with a constant density of 961 kg/m3 and a constant viscosity of 1.419×10-3 Kg/m.s is…

A: we are supposed to answer only 3 sub parts..please post other parts as the other question.

Q: In a laminar flow over plate the thickness of hydrodynamic boundary layer is 2 mm. What will be the…

A: Given, Thickness of hydrodynamic layer = δ = 2 mm Prandtl number = Pr = 2.54 Relation between…

Q: A 10-cm-diameter, 30-cm-high cylindrical bottle contains cold water at 3°C. The bottle is placed in…

A: Given:- Diameter of bottle=10cm height=30cm temp of cold water =3°C temp of air=27°C temp of water…

Question

100%

5 Air at 90°C and 1 atm flows over a flat plate at a velocity of 30 m/s. How thick is the
boundary layer at a distance of 2.5 cm from the leading edge of the plate?
ir Aows

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What are the turbulence intensity differences on offshore and onshore?
Water at 25°C and 1 atm is flowing over a long flat plate with a velocity of 8 m/s. Determine the distance from the leading edge of the plate where the flow becomes turbulent, and the thickness of the boundary layer at that location.
A 10-cm-diameter, 30-cm-high cylindrical bottle contains cold water at 3°C. The bottle is placed in windy air at 27°C. The water temperature is measured to be 11°C after 45 min of cooling. Disregarding radiation effects and heat transfer from the top and bottom surfaces, estimate the average wind velocity.
What is the effect of streamlining on (a) friction drag and (b) pressure drag? Does the total drag acting on a body necessarily decrease as a result of streamlining? Explain.
Q6: A large vertical plate 6.1 m high and 1.22 m wide is maintained at a constant temperature of 57+C and exposed to atmospheric air at 4°C. Calculate the heat lost by the plate. Answers: Q=1907 W
What are the three layers within turbulent flow? In which layer is the velocity smallest and in which layer is the turbulent portion of the shear stress dominant?
In flow over bluff bodies such as a cylinder, how does the pressure drag differ from the friction drag?
The airflow at 1 atm has a free stream velocity and temperature of 5 cm/s and 25°C, respectively. Determine the heat flux on the plate surface and the convection heat transfer coefficient of the airflow.
What fluid property is responsible for the development of the velocity boundary layer? What is the effect of the velocity on the thickness of the boundary layer?
Question No. 3: During a cold winter day, wind at 55 km/h is blowing parallel to a 4-m-high and 10-m-long wall of a house. If the air outside is at 5°C and the surface temperature of the wall is12°C, determine the rate of heat loss from that wall by convection. What would your answer be if the wind velocity was doubled
A 5-mm-diameter electrical transmission line is exposed to windy air. Determine the drag force exerted on a 160-m-long section of the wire during a windy day when the air is at 1 atm and 15°C and the wind is blowing across the transmission line at 50 km/h.
Consider a refrigeration truck traveling at 70 mi/h at a location where the air is at 1 atm and 80°F. The refrigerated compartment of the truck can be considered to be a 9-ft-wide, 8-ft-high, and 20-ft-long rectangular box. Assuming the airflow over the entire outer surface to be turbulent and attached (no flow separation), determine the drag force acting on the top and side surfaces and the power required to overcome this drag.