Q5 only Solve Q5 only4) A welded connection, as shown in Fig. 2,is subjected to an eccentric force of 60kN in the plane of the welds. Determine the sizeof the welds, if the permissible shear stress forthe weld is 200 N/mm2.60 kNW100W215050Fig. 25) Based upon data given in Fig. 2, theprimary shear stress generated in theeccentric loaded weld:29.72 MPa80.57 MPaO 120.58 MPaO 184.99 MPa

Answered: Image /qna-images/answer/e8b74a8f-7aff-4d2b-b6e0-684b6242b749.jpg

Answered: 5) Based upon data given in Fig. 2, the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the weld cannot exceed 3 in. If the weld must transmit a total force equal to 9600 lb, it’s size should be A. 1/2 in. B. 3/8 in. C. 5/16 in. D. 1/4 in.
A rectangular steel plate is welded as a cantilever to a vertical column and supports a single concentrated load P. Determine the weld size if shear stress in the same is not to exceed 140 MPa
A welded connection has an effective length of 150 mm. 12 mm fillet welds are used. If the ultimate strength of the weld is 485 MPa and its allowable shearing stress is 60% of Fuw. Determine the allowable shearing stress of the weld in MPa.
Q.2. A bar with a rectangular cross-section is weld as shown. Determine the size weld, if the pemissible shear stress in the weld 80 MPa. The rectangle area of a fillet weld is equal to [ 2t (b+/)]. 31KN
A steel railroad track (E=200GPa, α=11.7x10^-6/°C) was laid out at a temperature of -6°C. Determine the normal stress in the rail when the temperature reaches 48°C. Assuming that the rails (a) are welded to form a continuous track (b) are 10m long with 3mm gaps between them.
A bracket is welded to the verical column by means of two fillet welds as shown in the figure. Determine the size of the welds, if the permissible shear stress in the weld is limited by 70N/mm^2.
A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown below. The pressure in the tank is 2.76 MPa, and an axial load of 133.5 KN is applied to the end of the tank through a rigid bearing plate. Determine the normal stress and shearing stress perpendicular to the weld.
A 1/4 in fillet weld is to transmit a total force of 12,000 lb. If the allowable unit stress in shear on the weld is 15,800 psi, the minimum effective length of the weld must be A. 5.4 B 4.9 in C. 4.3 in D 3.9 in.
A steel plate, 80 mm wide and 10 mm thick, is joined toanother steel plate by means of a single transverse anddouble parallel fillet welds, as shown in figure. The strengthof the welded joint should be equal to the strength of theplates to be joined. The permissible tensile and shearstresses for the weld material and the plates are 100 and 70N/mm2 respectively. Find the length of each parallel filletweld. Assume that the tensile force passes through the centre of gravity of three welds.
The allowable stresses for the splice shown are the following: 150 MPa for shear of rivets, 1.35Fy for bearing,0.60Fy for tension and Fy = 250 MPa. Note: rivet holes are 2 mm bigger than the rivet diameter and the middleplate is 20 mm thick. Find the diameter of the rivets so that the joint capacity due to shear approximately equal to the bearingcapacity.a. 25.4 mm c. 28.65 mmb. 30.79 mm d. 36.97 mm Find the maximum safe value of P without exceeding the allowable shearing stressa. 773.6 kN c. 938.3 kNb. 878.1 kN d. 848.2 kN Find the maximum safe value of P without exceeding the allowable tensile stress.a. 579.3 kN c. 716.1 kNb. 495.5 kN d. 692.5 kN
The two steel members are joined together using a 30∘∘ scarf weld. Forces of F=12.5 kNF=12.5 kN are applied at each end, as shown. (Figure 1) PART A) Determine the average normal stress resisted in the plane of the weld. Express your answer to three significant figures and include appropriate units. PART B) Determine the average shear stress resisted in the plane of the weld. Express your answer to three significant figures and include appropriate units.
A cylindrical air-compressor tank with an inside diameter of 50 mm is to be designed to withstand safely a working pressure of 0.86 MPa. Boiler plate with an allowable tensile stress of 76 MPa. All seams will be butt welds with an expected efficiency of 100 percent. a.) Determine the force per lineal mm of longitudinal seam, b.) Determine the required thickness “t” of wall, c.) Determine the unit stress in the circumferential seam.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

5) Based upon data given in Fig. 2, the primary shear stress generated in the eccentric loaded weld: 29.72 MPa 80.57 MPa O 120.58 MPa 184.99 MPa