5) Consider the fragment of legv8 assembly below and suppose the pipeline is modified, so that it has only one memory (that handles both instruction and data ). In this case, there will be a structural hazard every time a program needs to fetch an instruction during the same cycle in which another instruction accesses data. Draw a pipeline diagram PLI: SUB LDUR ADD CBZ STUR ADD X2, X1, XO X13, [X3 , #8 ] X11, X2, XO X11, SON X13, [X3 #12 ] X2, X12, XO

5) Consider the fragment of legv8 assembly below and suppose the pipeline is modified, so that it has only one memory (that handles both instruction and data ). In this case, there will be a structural hazard every time a program needs to fetch an instruction during the same cycle in which another instruction accesses data. Draw a pipeline diagram PLI: SUB LDUR ADD CBZ STUR ADD X2, X1, XO X13, [X3 , #8 ] X11, X2, XO X11, SON X13, [X3 #12 ] X2, X12, XO

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter13: Magnetic Induction

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

Discuss different methods of moving a content from R2 to R1 register in 8051. Assume that Register Bank0 is selected. Compare all methods with respect to program size and execution speed. Also, mentionwhich method is the best.
Suppose that the contents of certain memory locations are as shown in Figure P8.34. Furthermore, for each part of this problem, the initial contents of the CPU registers are: ( D)=$0003,( X )=$1 FFF, and (Y)=$1000. Name the type of addressing and determine the contents of registers D, X, and Y after each of these instructions is executed: a. ADDB $1002,Y b. LDAA B,X c. LDAB 7, +X d. LDX [$1004,Y] e. LDAA [D,X]
When the value of the four-bit N number consisting of W, X, Y, Z variables is N <3 or N> 6, the circuit with a logic 1 output is designed with 8x1 MUX. When the W, X, Y variables are mutually connected to the S2, S1, S0 selection terminals of the multiplexer, in which case are the signals to be connected to the input terminals of the multiplexer correctly? (The variables will be used in the given order and W is MSB. The signals to be applied to the input terminals are written from I0 to I7.)
1. Write down 2- differences between Von-Neumann and Harvard architecture. 2. you are executing an instruction, SUB $s0, $s1, $s2 (address 0x20). Draw the datapath of this instruction when $s1=10, $s2=5. When are the stages in this datapath? Mark the components which are active in corresponding stages. 3. How to store(1050000)10 in register $s0? Write down the instructions that stores the data in $s0 register.
In cases where the value of the four-bit N number consisting of W, X, Y, Z variables is N <6 or N> 10, the circuit with a logic 1 output is designed with 8x1 MUX. When the W, X, Y variables are mutually connected to the S2, S1, S0 selection terminals of the multiplexer, in which case are the signals to be connected to the input terminals of the multiplexer correctly? (The variables will be used in the given order and W is MSB. The signals to be applied to the input terminals are written from I0 to I7.) A 1,1, Z',0,0,Z,1,1 B 1,Z',0,Z,1,1,1,1 C 1,0,0,0,Z,1,1,1 D 1,1,Z',0,Z,0,0,0 E 1,1,1,0,0,Z,1,1
A 4-bit universal shifting register QA, QB, QC and QD and a single serial input called SI, has two inputs so that they determine how to operate, as follows: M0M1 = 00 indicates that it should keep the value of the current outputs, M0M1 = 01 indicates that you should shift right, M0M1 = 10 indicates that you should shift left, and M0M1 = 11 indicates that you should parallel load inputs A, B, C, and D. Design a minimum circuit that implement this record and draw the final schematic diagram. Include the entire design procedure
Microprocessor 8085 : Note 1: Use F for fetch, R for memory read, W for memory write, IOR for IO read, and IOW for IO writeNote 2: Use hexadecimal where possible Q /- If register A contains (66 h) and CY=1, what is the result in the accumulator after (ADC A) instruction? - If register A contains (3A h) and register B contains (44 h), what are the results in the CY and Z flags after (CMP B) instruction?
Explain a XYZ method of transferring data from the computer's RAM to another part of the computer without processing it using the CPU. As a sound card may need to access data stored in the computer's RAM, but since it can process the data itself, XYZ is a means of having a peripheral device control a processor's memory bus directly. It permits the peripheral, such as a UART, to transfer data directly to or from memory without having each byte (or word) handled by the processor. Draw a diagram of the unit used in XYZ and how data is transferred using this method.
Write a Verilog code with testbench for 16-bit up/down counter with synchronous reset and synchronous up/down.If up/down is set the counter is up counter and if it is not set, the counter is a down counter. submit the module code, testbench code, and the simulation results. PLEASE EXECUTE CODE IN VERILOG
Question:If you have two functions F(a,b,c) and G(a,b,c) to implement, what mux size and how many muxes would you need to implement F & G?My Comments:Is it as simple as using two 4-1 multiplexers because it will handle the 6 inputs? Or am I not understanding the function of a multiplexer?
(i) Compute bitwise NOT A and place the result in A.(ii) Compute bitwise AND A, B and place the result in A(iii) Compute bitwise OR A, B and place the result in A(iv) Compute bitwise XOR A, B and place the result in A(v) Can PONY be used to compute ADD A, B, the 32-bit addition of registers? Please justify your answer.
Why using double command in matlab in this code ?