5. A balanced positive-sequence wye- connected 60-Hz three-phase source has line-to-line voltages of VL = 208 V rms. This source is connected to a balanced wye- connected load. Each phase of the load consists of an impedance of 30 + j40 №. Find the line-to-neutral voltage phasors, the line-to-line voltage phasors, the line-current phasors, the power, and the reactive power delivered to the load. Assume that the phase of Van is zero.

5. A balanced positive-sequence wye- connected 60-Hz three-phase source has line-to-line voltages of VL = 208 V rms. This source is connected to a balanced wye- connected load. Each phase of the load consists of an impedance of 30 + j40 №. Find the line-to-neutral voltage phasors, the line-to-line voltage phasors, the line-current phasors, the power, and the reactive power delivered to the load. Assume that the phase of Van is zero.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

Find the total impedance, voltage drop on the 100-ohm resistor, draw the phasor diagram of the voltage and current at R1, total power (apparent) delivered by the current source, draw the phasor diagram of the voltage and current at the source. Also, is the circuit inductive, capacitive, or neither (resistive)? please give the step-by-step solution NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
A balanced wye-connected three-phase source has line-to-neutral voltages of 240 V rms. Find the rms line-to-line voltage. This source is applied to a delta-connected load, each arm of which consists of a 10-Ω resistance in parallel with a +j5-Ω reactance. Determine the rms line current magnitude, the power factor, and the total power delivered.
A balanced wye-connected three-phase source has line-to-neutral voltages of 440 V rms. Find the rms line-to-line voltage magnitude. If this source is applied to a wye-connected load composed of three 30-Ω resistances, find the rms line-current magnitude and the total power delivered.
Two loads, A and B, are connected in parallel across a 1-kV-rms 60-Hz line, as shown in Figure P5.81. Load A consumes 10 kW with a 90 percent lagging power factor. Load B has an apparent power of 15 kVA with an 80 percent lagging power factor. Find the power, reactive power, and apparent power delivered by the source. What is the power factor seen by the source? Repeat Problem P5.81 if load A consumes 5 kW with a 90 percent lagging power factor and load B consumes 10 kW with an 80 percent leading power factor.
what is the mutual inductance in ohms (or the mutual inductive reactance ) between the two mutually-coupled inductors? if circuit to the left of load Z is converted into its Thevenin's equivalent, what would be the magnitude of ZTh in ohms? what is the phase angle of ZTh in degrees? what would be the phase angle of VTh in degrees? what would be the magnitude of VTh in volts if E = 120 V?
Consider a load impedance of Z=jwL connected to a voltage and V let the current drawn be I. (a) Develop an expression for the reactive power Q in terms of ,L, and I, from complex power considerations. (b) Let the instantaneous current be i(t)=2Icos(t+). Obtain an expression for the instantaneous power p(t) into L, and then express it in terms of Q. (c) Comment on the average real power P supplied to the inductor and the instantaneous power supplied.
A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
NOTE: Polar form for Voltage & Current. Rectangular form for Impedance Find the total impedance of the circuit, total power (apparent) delivered by the current source, Draw the phasor diagram of the voltage and current at the source, the current passing through the R2 and L1 branch, Draw the phasor diagram of the voltage and current at the R2 and L1 branch. Also, is the circuit inductive, capacitive, or neither (resistive)?
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are ________ and ____________ , respectively.
Describe the concept of microgrids in power distribution. What are the key components and benefits of implementing microgrids, especially in the context of renewable energy integration?
a-Calculate and draw the load current for the steady-state condition b-Find the RMS values of the load voltage and the load current