5. A bone containing a solid polymer filler actingas an implant is tested by the application of a2000N force to its midpoint. Assume thepolymer is perfectly bonded to the bone. Inthe central region of the bone, the cross-section is approximately circular.For the cortical bone, E₂ = 20 GPaFor the polymer, Ep = 1.8 GPa(a) Determine the location of the maximumbending moment in the system. .2m(b) Calculate the maximum bending stresses inthe bone and in the polymer at theinterface point H.7.03 Mpa78.13 Mpqalong lengthFor a circle, I = r²/4fromleftrelative to centroidendveslect smallangle herePTo = 12 mm40 cmBone, B|r₁ = 6 mmSolid PolymerfillePolymer, P

Answered: Image /qna-images/answer/db140c2e-eaf8-4684-abd4-ff9f067a1a1f.jpg

5. A bone containing a solid polymer filler acting as an implant is tested by the application of a 2000N force to its midpoint. Assume the polymer is perfectly bonded to the bone. In the central region of the bone, the cross- section is approximately circular. For the cortical bone, E₂ = 20 GPa For the polymer, Ep = 1.8 GPa Glong length (a) Determine the location of the maximum bending moment in the system. .2m (b) Calculate the maximum bending stresses in the bone and in the polymer at the interface point H. T 7.03 Mpa from left 78.13 Mpq For a circle, I = r²/4 relative to centroid end veslect small angle here. P To = 12 mm 40 cm Bone, B |r₁ = 6 mm Solid Polymer fille Polymer, P

5. A bone containing a solid polymer filler acting as an implant is tested by the application of a 2000N force to its midpoint. Assume the polymer is perfectly bonded to the bone. In the central region of the bone, the cross- section is approximately circular. For the cortical bone, E₂ = 20 GPa For the polymer, Ep = 1.8 GPa Glong length (a) Determine the location of the maximum bending moment in the system. .2m (b) Calculate the maximum bending stresses in the bone and in the polymer at the interface point H. T 7.03 Mpa from left 78.13 Mpq For a circle, I = r²/4 relative to centroid end veslect small angle here. P To = 12 mm 40 cm Bone, B |r₁ = 6 mm Solid Polymer fille Polymer, P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a) Determine the elements of the stiffness matrix [Q] for a lamina made from T300 carbon fiber/epoxy matrix. The lamina has the following properties, E1=133.44GPa, E2=8.78 GPa, v12=0.26, G12=91.7 GPa. b) Calculate the transformed stiffness matrix [Q] when the ply is oriented at 45 degrees.
A band of polymer is to hold together a bundle of steel rods for up to one year. if the stress on the band is less than 1300 psi, the band will not hold the rods tightly. determine the initial stress that must be applied to the polymer band when it is slipped over the steel. A series of tests showed that an initial stress of 1000 psi decreased to 980 psi after 5 days. (1yr. = 12 mos = 52wks)
The femur, the long bone in the thigh, can be modeled as a tube of compact bone for most of its length. The cross-section area of the compact bone in the femur of a 70 kg person is 4.8 x 10-4 m2, a typical value.a. If this person supports his entire weight on one leg, what fraction of the tensile strength of the bone does this stress represent?b. By what fraction of its length does the femur shorten?
A fiber reinfored rod contains 50 volume percent glass fiber ( E = 700 GPa) and 50 volume percent plastic ( E = 7 GPa) . The glass carries what part of a 5000 N tensile load ?
9. A compressive force of 15-N is applied to a flexible poly(vinyl chloride) (CAS# 9002-86-2) wire that is 5-m long and has a diameter of 3.6-mm. If the wire contracts by 0.5-mm, calculate the compressive modulus
A high-density polyethelene (HDPE) [E = 780 MPa; ν = 0.46] rod has a diameter of 100 mm before load P is applied. In order to maintain certain clearances, the diameter of the rod must not exceed 101 mm when loaded. What is the largest permissible compressive load P that can be applied to the HDPE rod?
A tensile load of 120N is applied to an aluminum boron composite with 1mm^2 cross sectional area.the volume of parallel fibers is 20%.what is the stress in the fibers when the load Axis is (a)parallel to the fibers (b)perpendicular to the fibers
A cylindrical pipe with diameter d = 1.0 m is subject to internal pressure p = 5.0 MPa but it is free to expand along the length so that only hoop stress o = pd/2t is developed in the wall. a. what is the optimum orientation for the fibers?, and why? b. what is the required wall thickness and material type that yields the minimum thickness? c. Compare the weight per unit length of the minimum weight pipe with a pipe made out of 6061-T6 aluminum with a yield strength of 270 MPa and density p = 2.70 g/cc Use the same load and resistance factors.
A 0 degree lamina of glass fiber-epoxy 3501 composite with fiber arranged withmax. volume fraction of fiber in a square array is subjected to a stress σx = 50MPa at theta =20 degrees. What are the resulting lamina strains [ε]xy and strains[ε]12? (Apply the Halpin-Tsai correction to transverse moduli and shear moduli)
Polyurethane are classified as Elastomer materials Select one: .True .False
A sample of cross-linked natural rubber (polyisoprene) is found to have a shear modulus of 100 kPa at 20˚C. Determine the force needed to stretch a 20 mm diameter by 100 mm long rod to 300 mm (stretched in the length direction). What is the diameter of this rod of natural rubber under such a load?
An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top plate displaces 2 mm horizontally when it is subjected to a horizontal force P = 2 kN, determine the shear modulus of the polymer. The width of the block is 100 mm. Assume that the polymer is linearly elastic and use small-angle analysis.