5. A projectile is fired downward in an experimental fluid and experiences an acceleration of a = o-nv², where o and n are positive constants and v representing the velocity. Determine the distance travelled by the projectile when its velocity has been reduced to half. Determine also the terminal velocity. Evaluate for a = 0.7 m/s², n = 0.2 ml, and initial velocity of 4 m/s.

5. A projectile is fired downward in an experimental fluid and experiences an acceleration of a = o-nv², where o and n are positive constants and v representing the velocity. Determine the distance travelled by the projectile when its velocity has been reduced to half. Determine also the terminal velocity. Evaluate for a = 0.7 m/s², n = 0.2 ml, and initial velocity of 4 m/s.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.26P: The velocity vector of the boat has two components: v1 is the velocity of the water, and v2 is the...

See similar textbooks

Similar questions

The flow rate is flowing Q=10+5t into the pipe whose cross-sectional area increases to A(x) = 1+x . Assuming that the pipe flow is one-dimensional, what is the acceleration when time t=1 at the pipe inlet(x=0)?
Determine the third velocity component v such that all the components satisfy the continuityequation. The two components are as follows:u = 2xt– 3xyz + 4xyw = 3x– 5yzt + yzAlso find the velocity and acceleration of a fluid particle at (1, 0, 1) at time, t = 1
Non-uniformly acceleratedmotion& Motion Curves 1.. The brake mechanism used to reduce a gun recoil consists of a piston attached to a barrelmoving in the fixed cylinder filled with oil. As the barrel recoils with an initial velocity v0, the piston moves and the oil is forced through the orifices in the piston, causing the piston and the cylinder todecelerate at a rate proportional to their velocities. Determine v (t), x (t), and v (x)
A fluid flows through pipe shown below of uniform diameter 15 cm. The velocity of the fluid particles on the streamline along the center line of the pipe defined by V = 3t m/sec . find the the normal acceleration and the streamline acceleration when t = 10 sec. 0.5 m
According to the potential equation of a two-dimensional flow in the horizontal plane defined as; i-) Is this current physically possible? Prove ii-) Determine the current function ψ (x, y) of this current. [ψ (0,0) = 0] iii-) Calculate the resultant velocity and resultant acceleration at point A (e, f) in this flow field. iv-) Calculate the flow rate passing between the streamlines ψ (a, a) and ψ (c, c).
When a valve is opened, a certain fluid flows through the choke duct or valve (see figure), according to the relationship: V= V (1 + x/L) i Determine a) If the flow is stationary or transient. b) The acceleration (ax) of the fluid applying Euler's approach. c) The position of the particle as a function of time at x = 0 and t = 0. d) Determine the acceleration of the particle as a function of time.
The flow of an oil is described by the velocity field: v= (3y)êx + (0.6t^2 + 2)êy Where t and y are measured in seconds and meters, respectively, such that the components of the velocities are expressed in m/s. a) If an oil particle was at the origin when t = 0s, determine its position in time t = 2s, and sketch the particle's path in the X-Y plane. b) What are the magnitude and direction of the particle's velocity at said instant of time? c) What are the magnitude and direction of the acceleration of the particle at said instant of time?
A piece of electronic equipment that is surrounded by packing material is dropped so that it hits the ground with a speed of 4 m/s. After contact the equipment experiences an acceleration of a- kx , where k is a constant and x is the compression of the packing material. If the packing material experiences a maximum compression of 20 mm, determine the maximum acceleration of the equipment.
The jet car is originally traveling at a velocity of 10 m/s when it is subjected to the acceleration shown. When t= 0, s = 0. Suppose that a1 = 4.5 m/s2 , a2 = -2.5 m/s2 , and t′' = 13 s Determine the car's maximum velocity. Express your answer to three significant figures and include the appropriate units.
The velocity of aparticle which moves along the x-axis is given by x = 40-3t² (m/s) where t is in seconds. Calculate the displacement Ax of the particle during the interval from t=2sec to = 4 sec.
A venturi tube is used to determine the airspeed at the throat/test section. During the test, a raise of 4.8 inches of water was recorded in the instrument. Determine the velocity of the at the (a) smallest and (b) largest section, when the ratio of the area between the largest and smallest section is 75:30. Assume incompressible flow and standard sea-level conditions.the answer should be v1 = 63.1962 ft/s and v2 = 157.9905 ft/s
The horizontal motion of the plunger and shaft is arrested by the resistance of the attached disk which moves through the oil bath. The velocity of the plunger is v0 = 3.1 m/s in the position A where x = 0 and t = 0, and the deceleration is proportional to v so that a = -kv where k = 0.32 s-1. Find (a) the velocity when t = 2.9 s, (b) the position x when t = 2.9 s, (c) the velocity when x = 4.2 m.