Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 33 kips, F₂ = 18 kips, F3 = 25 kips, and F4 = 38 kips, determine the absolute value of the axial load in rod (2). F₁ A F₂ (1) F₂ B F3 (3) F3 F₁ с D

Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 33 kips, F₂ = 18 kips, F3 = 25 kips, and F4 = 38 kips, determine the absolute value of the axial load in rod (2). F₁ A F₂ (1) F₂ B F3 (3) F3 F₁ с D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.8.3P

See similar textbooks

Similar questions

Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 20 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 5 kips, R = 20 kips and S = 28 kips. Calculate F1, F2, F3 and..
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F1 = 30 kips, F2 = 10 kips, F3 = 26 kips, and F4 = 37 kips, determine the absolute value of the axial load in rod (2).
In the design in the figure, a force of Fn=1912 N in the vertical plane and a torque of Md=916 Ncm in the clockwise direction of rotation act on a machine element with a diameter of D=200 mm on the shaft resting on the A and B bearings. If the angle of the force with the horizontal is b=49o, how many Newtons is the resultant radial force to be considered in the bearing calculation of the bearing A? 1-) The diameter of the machine element on which the force acts will not be taken into account in the calculation of the bearing forces (ie, it will be assumed that the Fn force acts on the axis of the shaft). 2-) Pi number will be taken as 3.14.
Please show complete solution with formula and free body diagramA rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
The figure shows the combined design of an angular contact ball bearing on two fulcrums. The radial loads R1 and R2 and axial load Fa of bearings 1 and 2 are shown in the figure. The relationship between the derived axial force S and radial load R is: S = 0.25R. Calculate the actual axial force of bearing 1 and bearing 2? Fa= 360N R1=4000N R2=4250N Problem 5) Figure
A central horizontal section of a hook is a symmetrical trapezium of inner width=67.5mm and of outer width =22.5mm. The depth of the section is 90mm. The hookcarries a load of 37.5kN. The load line passes through the centre of curvature. Theradius of the hook is 52.5mm. Determine the maximum compressive and tensilestresses in the section of the hook.
Please show the formula used and free body diagram A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
The lap joint is fastened with four ¾-inch diameter rivets. ➢ a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. ➢ b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. ➢ c. what is the maximum value of the load P (kips) that can be applied to the joint?
The lap joint is fastened with four ¾-inch diameter rivets. a. If the allowable shearing stress of the rivets is 14 ksi (kips per square inch), find the value of P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. b. if the allowable bearing stress for the plates is 18 ksi, find the value of the load P (kips) that maybe applied to the joint. Assume that the load is equally distributed among the rivets. c. what is the maximum value of the load P (kips) that can be applied to the joint?