5. A supertanker is 300 m long, 80 m wide (beam), and 25 m deep (draft). The ship moves at 14 knots through seawater at 4° C. Determine the following: (a) the thickness of the boundary layer at the stern of the ship. (b) The total skin drag acting on the tanker (c) The power required to overcome the drag force 6. Determine the skin drag and power in Problem 5, if the surface of the tanker has a roughness of 1.5 mm.

5. A supertanker is 300 m long, 80 m wide (beam), and 25 m deep (draft). The ship moves at 14 knots through seawater at 4° C. Determine the following: (a) the thickness of the boundary layer at the stern of the ship. (b) The total skin drag acting on the tanker (c) The power required to overcome the drag force 6. Determine the skin drag and power in Problem 5, if the surface of the tanker has a roughness of 1.5 mm.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.55P

See similar textbooks

Similar questions

Icebergs can be driven at substantial speeds by the wind.Let the iceberg be idealized as a large, flat cylinder, D >> L,with one-eighth of its bulk exposed, as in Fig.. Letthe seawater be at rest. If the upper and lower drag forcesdepend on relative velocities between the iceberg and thefluid, derive an approximate expression for the steady icebergspeed V when driven by wind velocity U.
A Mitsubishi A6M Zero which has a wing area of 22.44 square meters with a lift generated of 6,000 N. If the wingspan is 12 meters, Calculate the velocity at minimum thrust required at standard sea level conditions. Assume wing is an elliptical planform and parasite drag is 0.045.
Solve Parts A-C and label Them QUESTION: Suppose you buy a 3 x 7-ft sheet of plywood and put it on your roof rack. You drive home at 45 mi/h. Part A - If the board is perfectly aligned with the airflow, how thick is the boundary layer at the end of the board? Part B - Estimate the drag on the sheet of plywood if the boundary layer remains laminar? Part C - Estimate the drag on the sheet of plywood if the boundary layer is turbulent (assume the wood is smooth) and compare the result to that of the laminar boundary layer case. HINT - 3 X 7-ft sheet of plywood and put it on your roof rack. You drive home at 45 mi/h.
The original Flettner rotor ship was approximately 100 ftlong, displaced 800 tons, and had a wetted area of 3500 ft2. Assketched in Fig. , it had two rotors 50 ft high and 9 ft indiameter rotating at 750 r/min, which is far outside the range. The measured lift and drag coefficients for eachrotor were about 10 and 4, respectively. If the ship is mooredand subjected to a crosswind of 25 ft/s, as in Fig. whatwill the wind force parallel and normal to the ship centerlinebe? Estimate the power required to drive the rotors.
Flow straighteners are arrays of narrow ducts placed inwind tunnels to remove swirl and other in-plane secondaryvelocities. They can be idealized as square boxes constructedby vertical and horizontal plates, as in Fig. .The cross-section is a by a, and the box length is L. Assuminglaminar flat-plate flow and an array of N x N boxes,derive a formula for (a) the total drag on the bundle ofboxes and (b) the effective pressure drop across the bundle.
a)What is the impact of increasing Reynolds number on skin friction and pressure drags over an airfoil? What can be happened for separation in this case? b) What is an adverse pressure gradient and where does it occur on an airfoil (show that on a sketch)? c) Why lift-to-drag ratio is an important parameter for an aircraft? d)How can changing in altitude affect the aircraft power required, PR? Show thatmathematically and graphically?
Consider an NACA 2412 airfoil with a chord of 0.64 m in an airstream at standard sea level conditions. The freestream velocity is 70 m/s. The lift per unit span is 1254 N/m. Calculate the strength of the steady-state starting vortex.
Aerodynamics NACA 664-221 Chord c = 150 cm 1) What is the CL range to achieve the minimum coefficient of drag? 2) What is the thickness ratio of the airfoil?
A 30 cm diameter cork ball (S=0.21) is tied to the bottom of a river as shown. (a) Draw the free body diagram of the ball. (b) Calculate the tension in the string and the drag force on the ball. (c) Estimate the speed, Uo of the river current Hint: Volume of a sphere = (1/6)πD³.
Kindly give me both right solutions with clear calculations The drag polar of a glider is given by CD=0.01+0.022CL2 . If it is launched from a height of 400m in still air. Please determine:(a) the maximum lift to drag ratio ??;(b) the greatest possible ground distance it can cover.
The Antonov An-225 is the heaviest aircraft ever built, with a maximum takeoff weight of 640 metric tonnes. It also has the largest wingspan of any aircraft in operational service. Sea level standard day (sls) conditions for calculations are 15°C; 101.3kPa Rotate speed (Vr) at takeoff (sls): Vr = 154 kts = 1.2×Vmin (1 kt = 0.514 m/s) Cruise Engine Thrust : a) Calculate the lift coefficient for a standard day takeoff b) Calculate the drag coefficient at cruis Fcruise = 0.85 Fmax Engine maximum thrust: Factual,max = Fsls,max×δ θ½ δ = Pactual/Pref; and θ = Tref/Tactual
Compute for the lift force acting on a wing with an area of 56 sq. ft., velocity of 75 ft/s at an altitude of 5000 ft. Cl of the wing is 0.75. Calculate the drag of a certain wing with an area of 20 sq. meters , velocity of 75 m/s at an altitude of 2000m . Cd of the wing is 0.05. Compute for the drag of a rectangular wing with a chord of 4.5 ft and a span of 16 ft. if the dynamic pressure 80 psi. Cd of the wing is 0.030.