Choose a letter. Thanks! 1. In Figure A, 2=45°. What is the measure of 25?A. 30° B. 45° C. 60° D. 135°2. In Figure A, Z1=140°. What is the measure of 28?A. 40° B. 50° C. 140° D. 220°Given: v|| w3. In Figure B, Ze=35°. What is the measure dA. 35° B. 55° C. 125° D. 145°Figure B4. In Figure B, Zu=70°. What is the measure of Zs?A. 20° B. 70° C. 110° D. 290°5. If two lines are cut by a transversal, which of the following conditions isnecessary to say that corresponding angles are congruent?The two lines must_A. be parallel.B. be perpendicular.C. intersect.D. form angles.

When two lines are cut by a transversal, the angles which occupy the same relative position are…

Answered: 5. If two lines are cut by a…

Mathematics For Machine Technology

8th Edition

ISBN:9781337798310

Author:Peterson, John.

Publisher:Peterson, John.

Chapter67: Analysis Of Trigonometric Functions

Section: Chapter Questions

Problem 9A: Refer to the following figure in answering Exercises 7 through 13. It may be helpful to sketch...

See similar textbooks

Similar questions

The length, L, of the point on any standard 118° included angle drill, as shown in Figure 12-5, can be calculated using the formula L=0.3 O where represents the diameter of the drill. Determine the lengths of the following drill points with the given diameters. Round to 3 decimal places for inches and 1 decimal place for millimeters. a. 12 b. 14 c. 38 d. 10 mm e. 25 mm f. 45 mm
Refer to the following figure in answering Exercises 7 through 13. It may be helpful to sketch figures. When 1 is 0: a. What is the value of side y? b. How does side x compare to side r?
For Exercises 23 through 34, round the answers to 1 decimal place. 28. All dimensions in Figure 39-18 are in inches. Find the length of belt on the pulleys. Length of belt = 2C=11D+11d7+(Dd)4C
Refer to the following figure in answering Exercises 7 through 13. It may be helpful to sketch figures. When 1 is almost 90: a. How does side y compare to side r? b. How does side x compare to side r? c. How does side x compare to side y?
For Exercises 23 through 34, round the answers to 1 decimal place. 31. All dimensions are in inches. Find the shaded area of Figure 39-21. Area =(R2r2)2
For Exercises 23 through 34, round the answers to 1 decimal place. 27. All dimensions are in inches. Find the shaded area of Figure 39-17. Area=(H+h)b+ch+aH2
Refer to the drill jig shown. Determine 1.
Refer to the following figure in answering Exercises 7 through 13. It may be helpful to sketch figures. When 1 is slightly greater than 0: a. How does side y compare to side r? b. How does side x compare to side r? c. How does side x compare to side y?
Determine the distance AB if CO = 19.8 mm.
Use the information given in Figure 1 to find x, h, s, and r if y=3. (Note: s is the distance from A to D. and y is the distance from D to B .)
Three holes are bored in a checking gage. The lower left edge of the gage is the reference point for the hole locations. Sketch the hole locations and determine the missing distances. From the reference point: Hole #1 is 1332 to the right, and 158up. Hole #2 is 2164 to the right, and 2316up. Hole #3 is 314to the right, and 312up. Determine: a. The horizontal distance between hole #1 and hole #2. b. The horizontal distance between hole #2 and hole #3. c. The horizontal distance between hole #1 and hole #3. d. The vertical distance between hole #1 and hole #2. e. The vertical distance between hole #2 and hole #3. f. The vertical distance between hole #1 and hole #3.

Recommended textbooks for you

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Elementary Geometry For College Students, 7e

Geometry

ISBN:

9781337614085

Author:

Alexander, Daniel C.; Koeberlein, Geralyn M.

Publisher:

Cengage,

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Elementary Geometry For College Students, 7e

Geometry

ISBN:

9781337614085

Author:

Alexander, Daniel C.; Koeberlein, Geralyn M.

Publisher:

Cengage,

Algebra & Trigonometry with Analytic Geometry

Algebra

ISBN:

9781133382119

Author:

Swokowski

Publisher:

Cengage

Algebra: Structure And Method, Book 1

Algebra

ISBN:

9780395977224

Author:

Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. Cole

Publisher:

McDougal Littell

Trigonometry (MindTap Course List)

Trigonometry

ISBN:

9781305652224

Author:

Charles P. McKeague, Mark D. Turner

Publisher:

Cengage Learning

Holt Mcdougal Larson Pre-algebra: Student Edition…

Algebra

ISBN:

9780547587776

Author:

HOLT MCDOUGAL

Publisher:

HOLT MCDOUGAL

SEE MORE TEXTBOOKS

5. If two lines are cut by a transversal, which of the following conditions is necessary to say that corresponding angles are congruent? The two lines must_ A. be parallel. B. be perpendicular. C. intersect. D. form angles.