5. The slider P can be moved inward by means of the string S, while the slotted arm rotates about point O. The angular position of the arm is given by 0 = 0.81- where O is in radians and t is in 20 | seconds. The slider is at r= 1.6 m when t= 0 and thereafter is drawn inward at the constant rate of 0.2 m/s. Determine the magnitude and direction (expressed by the angle relative to the positive x- axis) of the velocity and acceleration of the slider when t= 4 s. Ans. 0.377 m/s, 259.5°; 0.272 m/s, 19.4° y -x-

5. The slider P can be moved inward by means of the string S, while the slotted arm rotates about point O. The angular position of the arm is given by 0 = 0.81- where O is in radians and t is in 20 | seconds. The slider is at r= 1.6 m when t= 0 and thereafter is drawn inward at the constant rate of 0.2 m/s. Determine the magnitude and direction (expressed by the angle relative to the positive x- axis) of the velocity and acceleration of the slider when t= 4 s. Ans. 0.377 m/s, 259.5°; 0.272 m/s, 19.4° y -x-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At the instant under consideration, the hydraulic cylinder AB has a length L = 0.75 m, and this length is momentarily increasing at a constant rate of 0.2 m∕s. If vA = 0.6 m∕s and ? = 35°, find the rate of change of the length L in m/s, in order for the velocity of the slider B to be 0.15 m/s.
The disk with radius r = 0.2 m (figure below) starts from rest and receives an angular acceleration at clockwise given by alfa= (3t3)rad/s2, where t is given in second. That said, for t = 3 s determine: (a) the angular velocity of the disk (b) the velocity intensity of a point P on the edge of the disk. Represent the direction of the velocity vector at point P indicated in the figure (c) the intensities of the normal and tangential components of the acceleration of a point P in the edge of the disc. Plot the direction of these acceleration components at the indicated point P in the figure
It is known that the static frictional force between block B and the plate will be overcome and the block will slide when its acceleration reaches 3 m / s2 (Figure 7b_4). If the plate starts from rest at t = 0 s and accelerates uniformly at a rate of 4 rad / s2 , determine the time t and the angular speed of the plate when the block starts to slip (r = 200 mm).
Rotation of bar OA is controlled by the lead screw which imparts a horizontal velocity v = 31 mm/s to collar C and causes pin P to travel along with the smooth slot. The velocity of collar C is decreasing at a rate of 5 mm/s2 at the instant in question. Determine the values of r¨ and θ¨, where r = OP, if h = 245 mm and x = 185 mm.
At the instant shown in the figure below, the arm AB of the conveyor belt is rotating about the Y axis with a constant angular velocity ω1 = 12 rad/s, while the arm is rotating upward at a constant rate ω2 = 8 rad/s. At that instant, the package is a distance r = 12 m from A, and the conveyor belt is running at a constant speed of ̇r = 10 m/s. Determine the velocity and acceleration of the package P at the instant shown. Neglect the size of the package.
The horizontal motion of the plunger and shaft is arrested by the resistance of the attached disk which moves through the oil bath. The velocity of the plunger is v0 = 3.8 m/s in the position A where x = 0 and t = 0, and the deceleration is proportional to v so that a = -kv where k = 0.61 s-1. Find (a) the velocity when t = 5.5 s, (b) the position x when t = 5.5 s, (c) the velocity when x = 3.5 m.
A weight is attched to a chord and forms aconical pendulum when it was rotated about thevertical axis. If the period of rotation is 0.2 sec, determine the velocity of the weight, in m/s, ifthe chord makes an angle of 25 degrees with thevertical.
Collars A and B are attached by a rod of length 30 cm, as shown below. The joint at A is a ball-and-socket and at B a pin joint. Collar A moves in the z direction, while the guide bar for collar B is on xy plane. At the instant shown, collar A is at a height of 24 cm and collar B is moving with a speed of 3 m/s towards the x axis. Find the (a) angular velocity of the rod, and (b) the sliding of collar B. Use the image attached to solve the question
The bucket is hoisted by the rope that wraps around a drum wheel. Ifthe angular displacement of the wheel is θ= (0.5t3 + 15t) rad, where tis in seconds, determine the velocity and acceleration of the bucketwhen t = 3s.
Consider the portion of an excavator shown. At the instant under consideration, the hydraulic cylinder is extending at a rate of 5 in./sec, which is decreasing at the rate of 2 in./sec every second. Simultaneously, the cylinder is rotating about a horizontal axis through O at a constant rate of 13 deg/sec. Determine the velocity v and acceleration a of the clevis attachment at B. Determine the indicated terms used in the velocity and acceleration formulas. Answers: r = __ in. θ = ___ ° r˙ = __in./sec θ˙ = ____ rad/s r¨ = ___ in./sec2 θ¨ = ____rad/s2
A train is moving horizontally to the right with the speed of VT=60 mi/h. Meanwhile, a car is traveling toward the train with the speed of VC=30 mi/h and a 30deg angle with respect to horizontal direction. Select the correct expression of the velocity vector of the train relative to the car ___________mi/h A. (60-30cos30°)-30sin30° B. (60-30cos30°) +30sin30° C. (60+30cos30°)-30sin30° D. (30cos30°-60) +30sin30°
Collars A and B are attached by a rod of length 30 cm, as shown below. The joint at A is a ball-and-socket and at B a pin joint. Collar A moves in the z direction, while the guide bar for collar B is on xy plane.At the instant shown,collar A is at a height of 24cm and collar B is moving with a speed of 3 m/s towards the x axis. Find the (a) angular velocity of the rod, and (b) the sliding of collarB.