5. Two bars are used to support a load. When unloaded, AB is 5 in. Iong, AC is 8 in. long, and the ring at A has coordinates (0, 0). If a load Pacts on the ring at A, the normal strain in AB becomes CAB = 0.02 in/in., and the normal strain in AC becomes CAC = 0.035 in/in. Determine the coordinate position of the ring due to the load. 5 in. 8 in.

5. Two bars are used to support a load. When unloaded, AB is 5 in. Iong, AC is 8 in. long, and the ring at A has coordinates (0, 0). If a load Pacts on the ring at A, the normal strain in AB becomes CAB = 0.02 in/in., and the normal strain in AC becomes CAC = 0.035 in/in. Determine the coordinate position of the ring due to the load. 5 in. 8 in.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.4.3P: A 4.75-in, outside diameter polyethylene pipe designed to carry chemical waste is placed in a trench...

See similar textbooks

Similar questions

A 4.75-in, outside diameter polyethylene pipe designed to carry chemical waste is placed in a trench and bent around a quarter-circular 90° bend (see figure). The bent section of the pipe is 52 ft long. Determine the maximum compressive strain If the normal strain cannot exceed 6.1 × 10-3 , what is the maximum diameter of the pipe? If d = 4.75 in., what is the minimum acceptable length of the bent section of the pipe?
Solve the preceding problem (W 250 × 44.8) if the resultant force P equals 110 kN and E = 200 GPa.
The strain at point A on a beam has components Px = 450(10-6), Py = 825(10-6), gxy = 275(10-6), Pz = 0. Determine (a) the principal strains at A, (b) the maximum shear strain in the x–y plane, and (c) the absolute maximumshear strain.
Two fully loaded tractor trailers travel over the bridge putting substantial loading on the structure. As they pass over the middle of the bridge, one of the vertical supporting pillars, which is fixed at its bottom, deforms as shown below. The weight of the trucks causes point T to move to point T'—a distance of 2.5 cm along the x-axis. If the pillar has an original height of 27 m , find the shear strain at point T.
The state of strain at a point on a wrench has components ϵx = 120(10-6), ϵy = -180(10-6), γxy= 150(10-6). Use Mohr's circle to solve the problem. Determine the orientations of the element at which the principal strains occur. θp1= θp2=
A rectangular block has dimensions of 3 in, 4 in, and 5 in along the X-, y-, and z- axes, respectively. The block is subjected to triaxial loading of three uniformly distributed loadings of 30 kips (C), 45 kips (T), and 60 kips (C) along the x-, y-, and z- axes, respectively. If the strain along the X- axis and the z-axis are 0.00021 (C) and 0.00042 (T), respectively, determine the Poisson's ratio and the modulus of elasticity of the material. Also, what is the change in volume of the material?
The rigid beam is supported by a pin at A and wires BD and CE. If the load P on the beam causes the end C to be displaced 15 mm downward, determineA. the normal strain developed in wire CEB. the normal strain developed in wires BD. Show free body diagram and complete solution (no shortcut) SHOW PRESSURE DIAGRAM. THANK YOU
Four axially loaded members are shown below. All members have the same value for E (Young’s modulus). Rank the members from largest to smallest absolute value of the average normal strain perpendicular to the applied load at cross section a-a shown in the figure.
A rigid steel bar is supported by three rods, as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rod (2) is 1020 μin./in. Assume initial rod lengths of L1 = 148 in. and L2 = 78 in. Determine(a) the normal strain in rods (1).(b) the normal strain in rods (1) if there is a 0.043 in. gap in the connections between the rigid bar and rods (1) at joints A and C before the load is applied.(c) the normal strain in rods (1) if there is a 0.043 in. gap in the connection between the rigid bar and rod (2) at joint B before the load is applied.
A cantilever beam with a rectangular cross section (width b = 20 mm, height Ii = 175mm) is loaded by a force P that acts at the mid-height of the beam and is inclined at anangle a to the vertical (see figure). Two strain gages are placed at point C, which also isat the mid-height of the beam. Gage A measures the strain in the horizontal direction,and gage B measures the strain at an angle = 600 to the horizontal. The measuredstrainsaree A = 145 X 10_6 and 68 = —165 X lO_6.Determine the force P and the angle a, assuming the material is steel with £ = 200 GPaand v = 1/3.
The L2 steel bolt as shown in Figure Q4 has a diameter of 5 mm, and the link AB which is made from stainless steel 304 has a rectangular cross section that is 14 mm wide by 4 mm thick. The bolt is tightened so that it has a tension of 1750 N. Neglect the hole in the link. The modulus of elasticity are, EL2 = 200 GPa and E304 = 193 GPa.(a) Determine the strain energy in the link AB due to bending. (b) Determine the strain energy in the bolt due to axial load.
Question # 1 Fig 2 shows an unstressed aluminum plate 2/4 inches thick. A circle of 9.5 inches diameter is scribed on it. Normal stresses of 15 ksi and 22 ksi, along x and y direction, are caused by forces acting in the plane of the plate. For Poisson's ratio 4 and modulus of elasticity 10 *10^6psi,then determine the following (a)change in the length of diameter AB (b)change in diameter CD (c)variation in the plate thickness (d)the volume change of the plate