5. What is the difference between Self Excited and Separately Exited DC motor? 6. We know there are few conditions for alternator synchronization. How many conditions are there? Write all the conditions. 7. Calculate the mechanical output power by the shunt-wound DC motor when the torque is 1.2 N-m and speed 1500 rpm

5. What is the difference between Self Excited and Separately Exited DC motor? 6. We know there are few conditions for alternator synchronization. How many conditions are there? Write all the conditions. 7. Calculate the mechanical output power by the shunt-wound DC motor when the torque is 1.2 N-m and speed 1500 rpm

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 19RQ: Why is the starting torque per A of starting current of a wound-rotor motor higher than that of a...

See similar textbooks

Similar questions

A synchronous motor is running at 75 percent of rated load with unity power factor. If the load increases to the rated output power, how do the following quantities change? a. field current; b. mechanical speed; c. output torque; d. armature current; e. power factor; f. torque angle.
A 6-pole, 50 Hz, 3-phase induction motor runs at 960 rpm while delivering a shaft torque of 120 N-m. If friction and windage loss amount to 180 W., determine the rotor copper loss.
Electrical Engineering Explain briefly in maximum of two sentences why the series wound DC motor type hasa higher starting torque?
Draw the torque vs Speed characteristics of series-wound DC motor and shunt DC motor. At the time of starting which DC motor must be loaded with 50/60 of the total load and why? [explain with equation].
a) In the experiment of performance study of three-phase wound rotor induction motor, what are the effects of adding an external rotor resistance on the following? 1. Motor Slip 2. Motor efficiency 3. Motor starting torque 4. Motor starting current 5. Input power factor 6. Magnetizing current 7. Developed torque 8. Maximum torque
A 6-pole, 50 Hz, 3-phase induction motor with a rotor resistance of 0.25 ohm develops a maximum torque of 10 Nm at 875 rpm. The rotor reactance and slip at maximum torque is ?
A 6-pole, 60-Hz, Y-connected, three-phase induction motor develops a torque (Td) of 250 N.m at a speed of 720 rpm. The rotor resistance is 0.4 Ohm/phase, and the stator winding impedance is negligible. A) What is the air-gap power? B) What is the rotor current refered to the stator? C) If the rotational loss is 1kW, what is the motor output power in hp?
A four-pole, three-phase induction motor drives aturbine load. At a certain operating point the machinehas 4 percent slip and 87 percent efficiency. The motordrives a turbine with torque–speed characteristic givenby TL = 20 + 0.006ω2. Determine the torque at themotor-turbine shaft and the total power delivered tothe turbine. What is the total power consumed by themotor?
{Q.1} A three-phase induction motor runs at almost 1198 revolutions per minute (rpm) at no load and 1112 rpm at full load when supplied from a 60-Hz, three-phase source. (a) How many poles does this motor have? (b) What is the slip in percent at full load? (C) What is the corresponding frequency of the rotor currents? (D) What is the corresponding speed of the rotor field with respect to the rotor and with respect to the stator?
A series dc motor 20-hp, 500-V, is having armature, series field and shunt field winding resistances of 0.08 Ω, 0.3 Ω and 125 Ω, respectively. If the back – emf is 478 V, determine the motor current when the connection is a) long – shunt. b) short – shunt c) series d) shunt
The armature resistance of a compound direct current motor with a short shunt connection is 0.15Ω , series winding resistance 0.25Ω and shunt winding The resistance is given as 800Ω. The armature of the DC motor with a terminal voltage of 120 is 1400 rpm. If it draws 12 amps from the motor terminals while rotating, the torque produced by the motor and Find the efficiency of the engine.
Type your question here A 6- pole, 50 Hz 3-phase induction motor has a full load slip of 4 percent. The rotor resistance and reactance per phase are 0.24 2 and 2 2 respectively. Calculate: a) The speed at the maximum torque and full load torque. b) The resistance to be added to the rotor circuit to obtain 60% of the