5/28 The design characteristics of a gear-reduction unit are under review. Gear B is rotating clockwise with a speed of 300 rev/min when a torque is applied to gear A at time t = 2s to give gear A a counterclock- wise acceleration a which varies with time for a duration of 4 seconds as shown. Determine the speed Ng of gear B when t = 6 s. rad CCW www. H www +6+ www www -2b- Problem 5/28 A 2 t, s 6

5/28 The design characteristics of a gear-reduction unit are under review. Gear B is rotating clockwise with a speed of 300 rev/min when a torque is applied to gear A at time t = 2s to give gear A a counterclock- wise acceleration a which varies with time for a duration of 4 seconds as shown. Determine the speed Ng of gear B when t = 6 s. rad CCW www. H www +6+ www www -2b- Problem 5/28 A 2 t, s 6

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two spur wheels with involute teeth gear together externally. The pitch circle diameters are 120 mm and 300 mm and the smaller wheel has 19 teeth. The pressure angle is 20o and the addendum is 0,3 of the circular pitch. Determine 1.1 The length of the arc of approach if the smaller wheel is the driver, and 1.2 The maximum velocity of sliding between the teeth when the driver rotates at 200 r/min
To understand rigid-body rotation about a translating axis. An exhausted bicyclist pedals somewhat erratically. The angular velocity of the front tire, as measured with respect to an axis fixed at the tire’s center, is given by ω(t)=12t−14sin(2t) for t≥0 where t represents the time in seconds and ω(t) is measured in radians per second. Assume that the tires roll without slipping The bicycle’s front tire has a spot of paint on it. Take the spot’s position at time t=0.00s to be at angle θ=0.00 radians with respect to an axis parallel to the ground (and perpendicular to the axis fixed at the tire’s center) and take angles in the direction of the tire's rotation to be positive. What angular displacement θ(2) has the spot undergone between 0.00 and 2.0 s? If the tire’s radius is 23 cm, what is d, the magnitude of the spot’s displacement after 2.0 seconds? Which one of the following statements describes the spot’s motion at t=2.0s? The wheel’s angular acceleration is constant and the…
Original Question: The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC,which in turn rotates about the terminal axis at O. At the instant shown, theangular velocity of the shaft OC is 10j rad/sec, and gear A is stationary. Deter-mine the angular velocity of gear B, and the velocity of a point D at the top ofgear B QUESTION THAT NEEDS TO BE ANSWERED: For the bevel gear system shown in problem above, determine the angular accelera-tion of gear B when gear A is stationary and member OC has an angular velocityof 10j rad/sec and and angular acceleration of 25j rad/sec2
A cyclist pedals constantly at 7.9587 rad/s the wheels are 336.5mm in radius. If the chain is directly connected with the sprockets which are 76 mm in radius (front sprocket) and 35mm in radius (rear sprockets), Determine the angular speed of the wheel in rad/s.
15.8 The gears A, B, and C, of radii rA=500 mm, rB=200 mm, rC=150 mm, respectively, all rotate around fixed axes parallel to the x-axis shown. At a certain instance, gear A rotates with wA=6i rad/s and gear C rotates with aC=10 rad/s2. Determine wB and aB at this instant.
A three-stage automobile transmission is shown schematically. The number 6 crankshaft has an angular angle of 50 rad / s.Find the angular velocity (w1) of the drive shaft no. 1 as it rotates with speed [w6 = 50 rad / s]. Each of the spur gears has a fixedrotates around the axis. It should be noted that gears 6 and 5, 4 and 3, 2 and 1 engage each other.. Division Circle of Gearsdiameters d6 = 180mm; d5 = 60mm; d4 = 60mm; d3 = 100mm; d2 = 140mm and d1 = 120mm.
Two mating involute spur gears of 20 pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length cach, find: i) the addendum for pinion and gear wheel, i) the length of arc of contact, iiithe maximum velocity of sliding during approach and recess. Assume pinion to be driver.
Two inclined shafts are connected by means of a universal joint. The speed of the driving shaftis 1000 £p.m. If the total fluctuation of speed of the driven shaft is not to exceed 12.5% of this, what is the maximum possible inclination between the two shafts? With this angle, what will be the maximum acceleration to which the driven shaft is subjected and when this will occur ? [Ans. 20.4° ; 1570 rad/s? ; 41.28°]
Assuming there is no slippage for the belt assembly below, Determine the following: (a) What is the angular velocity of each pulley if the belt has a constant speed of 5 m/s? What is the frequency and the period of each pulley? (b) What is the average angular velocity of each pulley if the rope accelerates from 5 m/s to 10 m/s in 10 s? How many revolutions does the pulley turn in that time? R 1 = 0.3 mR 2 = 0.2 mR 3 = 0.1 m
DO NOT INCORPORATE I-J-K IN THE SOLUTION!!! Gear A is between a stationary gear rack F and the gear rack E, which imoving at VE = 6 ft/s to the right at the instant shown. It is also observed that the acceleration of gear A is 2 ft/s2 also to the right. At this same instant, determine the angular velocity and angular acceleration of disk B. Use RMA for velocity analysis.
The constant angular acceleration of the rotating disk is 12 rad/s . The angular velocity of the disk is 24 rad/s clockwise when t = 0. Determine the total angle turned by the disk between t = 0 and t = 4sec. the answer is 48 rad. show your solution.
A pair of gears, having 40 and 30 teeth respectively, are of 25° involute form. Theaddendum length is 5 mm and the module is 5.5 mm. If smaller wheel is the driver androtates at 1500 r.p.m. find the velocity of sliding at the point of engagement and at thepoint of disengagement.