6- Design and sketch a 3-bit synchronous counter using J-K flip-flops which counts in the sequence: 100, 011, 001, 111, 101, 010, repeat 100, ... a) Make a state diagram showing the transition of the states. b) Draw a truth table showing the changes required in the inputs including each J and each K. c) Show the K-map you used for simplifying each J and K. d) Write the Boolean equation for each J and K. e) Draw the counter circuit.

6- Design and sketch a 3-bit synchronous counter using J-K flip-flops which counts in the sequence: 100, 011, 001, 111, 101, 010, repeat 100, ... a) Make a state diagram showing the transition of the states. b) Draw a truth table showing the changes required in the inputs including each J and each K. c) Show the K-map you used for simplifying each J and K. d) Write the Boolean equation for each J and K. e) Draw the counter circuit.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

3(a): Consider the following circuit, which uses two D flip-flops with falling edge triggers along with -bit full adder. The flip-flops are controlled by a single clock, C. Suppose C, Q0 and Q1 all initially have the value 0. First, fill in the blanks in the "i " = 0 (initial state)" row to show the values of D0 and D1 at this initial time (assume the results of the adder have had time to stabilize) . Next, show the values of Q0 , Q1, D0 , and D1 once they have stabilized after the ith falling edge of the clock, where i ranges from 1 to 4. Note that both the A and Carry In inputs of the adder are (Q not ) Q'0 not Q0 None of these first four rows should be the exactly the same.
Design a 2-bit synchronous counter using D Flip-flops. That is the counter should go through the sequences 10-01-11-00-10 not 00-01-10-11. Draw the state diagram, show the state transition table, write the flip-lops input equations and k-map and draw the final design using logisim.
Please show solution to answer The state diagram for a sequential circuit appears in the following figure. Make a state assignment for the circuit using 3-bit codes for the six states; make one of the code bits equal to the output to save logic, and find the encoded state table. The next states and outputs are don’t cares for the two unused state codes.
1) Design a synchronous counter by taking account the following counting order;0-5-1-4-6-7-3-0-5-1-4-6-7-3...
5.11 Implement a 4-bit down counter with D flip flops by doing the following.[1] How many flip flop is needed to implement this counter?[2] Derive a state diadram for this counter.[3] Derive a truth table for this counter.[4] Develop state input equations[5] Sketch a logic diagram for this counter.
Design a counter using D Flip Flops and J-K Flip Flops with a rising edge clock which counts in the sequence 0000,0001,0010,0011,0100,1011,1100,1101,1110,1111 and then repeats. The output signals are QA( MSB), QB, QC, QD (LSB) the input signals are A (MSB), B, C, D (LSB) - State and transition table of the design using D Flip Flops - State and transition table of the design using J-K Flip Flops - Grouped and Labelled K-Map of the designs - Minimized functions of the designs
Type your question here Design a 4-bit up-down synchronous counter using D, T, and J-K Flip-Flops
Based on your perspective, briefly discuss the structure of the different types of binary codes. What are the differences between asynchronous and synchronous sequential logic circuits? Rationalize your answer. Design a simple logic circuit for a Set/Reset (SR) Latch, based on any actual application of latches. Describe your design using at least three (3) sentences. Give three (3) applications of Flip-flops, and describe the process of each.
Design 3+R-bit Asynchronous up and down counter using T Flip Flop. Design must include characteristic table, truth table, K-Map and state diagram. R=((Remainder of (Roll Number/2))+1) Note: Roll no is 25 Implement the circuit into software.
State diagram given for a sequential circuit with 3 flip-flops A,B,C and 1 input X and 1 output Y. Design this circuit with D flip-flops using binary coding. (You should set unused states as "don't care".)
Please written by computer source Question 1 a. Tri-state logic is often used in digital design to resolve the conflict that arises when more than one output is connected. With the aid of a diagram, explain how this can be used in a digital design to share a single bus. b. Examine the following VHDL statements and draw a synthesised schematic for the corresponding design. c. Using concurrent statements only, (no process), describe a decoder in VHDL which satisfies the following conditions, and draw the High level RTL schematic for this design. 3 inputs (A, B, C) and 1 output (Z). The output is equal to 1 when either input A is equal to 1 or only input C is equal to 1. All signals are of type 'std_logic d. VHDL allows the designer to describe hardware using different language constructs. Although, these constructs might have the same, or similar, functionality, the result of the synthesis is quite different. One example is the if-else and the case constructs. Explain the difference…
Using the truth table Supplied with the knowledge of the full adder design, implement a four-bit adder Draw the diagram below. (TIP: Employ cascading technique For 2 Construct the four-bit adder circuit; test for the results of the following expressions and write the answer