-6 ft 6 ft-

Q: H1 y [m] ml L1 m2 H2 x [m] (horizontal) Two rectangular sheets are glued together to form a rigid…

A: Given: Let us consider the given figure, Create the system's equilibrium equations. Calculate the…

Q: Determine the resulting internal loads on the cross section through point C in the grippers. It has…

A: Given Applied load = 20 N To find Freebody diagram Internal loading at C

Q: 100 mm 100 mm 300 mm 50 mm E В C D 200 mm F 150 N A

A: As from above diagram computing θ=0Take moments about B  ΣΜB = 0  (AX)(200)-(150) (500) = 0  200AX =…

Q: The assembly consists of a 6061-T6-aluminum member and a C83400-red-brass member that rest on the…

A:

Q: Solve the reinforcement using the method of nodes. Calculate the reactions and forces in the bars…

A: Consider the following FBD Reactions can be calculated by equilibrium equations Taking sum of…

Q: The post is made from 606l-T6 aluminum and has a diameter of 50 mm. It is fixed supported at A and…

A: Given data Diameter of the post Dp= 50mm Force applied on the spring P = 40kN Spring constant K =…

Q: The beam is supported by the three pin-connected suspender bars, each having a diameter of 0.5 in.…

A: Given data: *The diameter of the bar is d=0.5 in. *The modulus of elasticity of the A-36 steel is…

Q: 5-6. Assume that each member of the truss is made of steel having a mass per length of 4 kg/m. Set P…

A:

Q: Q10a Assuming the pulley system below is weightless and frictionless pulley, determine reaction…

A: As it is seen from the diagram that the The Pulley and string system is attached with the ceiling at…

Q: The post is made of Douglas fir and has a diameter of 100 mm. If it is subjected to the load of 20…

A: Write the expression of the frictional resistance considering the distribution of load as triangular…

Q: The truss is made from A992 steel bars, each of which has a circular cross section with a diameter…

A: The given problem will be solved by calculating the force in every member of the given truss. Then…

Q: R9-7. The rigid link is supported by a pin at A and two A-36 steel wires, each having an unstretched…

A:

Q: Q1. The forearm and biceps support the 10-kg load at A. If, the smallest cross sectional area of the…

A: First of all, make a FBD of the diagram as shown below,

Q: FS-4. Determine the greatest load P that can be applied to the truss so that none of the members are…

A:

Q: Q6) The bar intended to support two vertical loads F1 and F2. If the cable CB can sustain a maximum…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: The torsional spring at B is undeformed when bars OB and BD are both in the vertical position and…

A: Understand that using properties of triangles AC=AB=b/2. Therefore, CE=b/2. Consider Ax and Ay be…

Q: If the gap between C and the rigid wall at D is initially 0.15 mm, determine the support reactions…

A:

Q: Q2 / The boom is intended to support two vertical loads, F, and F2. If the cable CB can sustain a…

A:

Q: The uniform links AB and BC each weigh 2 lb and the cylinder weighs 20 lb. Determine the horizontal…

A: Given data Weigtht of the cylinder Wc = 20lb Weight of the link AB Wab= 2lb Weight of the link BC…

Q: The clamp is adjusted so that it exerts a pair of 145-N compressive forces on the boards between its…

A: Taking the lower part of the clamp and drawing the free body drawing for the lower part –

Q: The residential building is constructed using fink roof truss system and the trusses are uniformly…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: The 10-lb weight is supported by the cord AC and roller and by a spring. If the spring has an…

A:

Q: The post is made from 606l-T6 aluminum and has a diameter of 50 mm. It is fixed supported at A and…

A: The data given is, Load, P = 50 kN Modulus of elasticity, E=68.9×109 The diameter of the rod, d =…

Q: The 30-N force causes the bar to tip 8 = 15 when the force is applied. Originally the bar is…

A: Given   Force at point C, Fc = 30 kN                        Angle = 15o Find   Stiffness of the…

Q: H1 y [m] ml LI m2 H2 x [m] (horizontal) Two rectangular sheets are glued together to form a rigid…

A: Draw the free-body diagram of the system.

Q: the pipe AB is screwed in tightly to a pipe flange attached to the wall. It has two forces acting on…

A: Now as per above FBDWe have∑Fx=0Rx+FBx+Fcx=0Rx+2+1=0Rx=-3 ∑Fy=0 Ry+FBy+Fcy=0 Ry+6-2=0 Ry=-4  ∑Fz=0…

Q: R9-7. The rigid link is supported by a pin at A and two A.36 steel wires, cach having an unstretched…

A: Given    Force, F = 1.75 kN     Area, A = 78 mm2

Q: The door has a weight of 90 lb. Its center of gravity is shown in the figure by point G. If the…

A: Draw the FBD for the given question.

Q: Q6) The bar intended to support two vertical loads F, and F,. If the cable CB can sustain a maximum…

A:

Q: The A-36 steel pipe has an outer radius of 20 mm and an inner radius of 15 mm. If it fits snugly…

A: For the given steel pipe connection and the load applied, the reactions at the fixed ends are as…

Q: The load is supported by the four 304 stainless steel wires that are connected to the rigid members…

A: Given: P = 500 lb   To find: Angle of tilt of the members AB and DC.

Q: Members AC and AB support the 300-lb crate. Determine the tensile force developed in cach member. 4

A: Find the force in each member.

Q: 2. A machine operator produces the tension Tin the control rod by applying the force Pto the foot…

A:

Q: The coupling rod is subjected to a force of 5 kip. Determine the distance d between C and E…

A: Given: The force on coupling rod is P = 5 kip. The unstretched length is spring is d = 10 in. The…

Q: Determine the force in member CG. The force is positive if in tension, negative if in compression.…

A:

Q: The composite aluminum 2014-T6 bar is made from two segments having diameters of 7.5 mm and 15 mm.…

A: Given: D1= 7.5 mm D2=15 mm m= 10 kg h=100 mm To determine: maximum axial stress developed in the bar

Q: The jib crane is pin connected at A and supported by a smooth collar at B. If x = 8 ft, determine…

A: Given data :  (jib crane)x = 8 ftAB= 12 ftw = 5000 lbpin connected at Asmooth collar at BTo find…

Q: Q4) Determine the magnitude of the horizontal force F and the support reactions at pin A. If the…

A: Free body diagram FREE BODY DIAGRAM is a diagram of the system which represents all the forces…

Q: Members AC and AB support the 300-Ib crate. Determine the tensile force developed in member (AB). 3…

A: Given:Crate weight=300 lb

Q: The pulley at D is frictionless and the cylinder weighs 100 lb. a. Determine the vertical reaction…

A:

Q: Determine the greatest force F that can be applied to the ring if each cable in (Eigure 1) can…

A:

Q: The bracket is held to the wall using three A-36 steel bolts at B, C, and D. Each bolt has a…

A: Given data as per the question Diameter of bolt =0.5 in  The force applied at bracket = 800 lb…

Q: The two A-36 steel bars have a thickness of 1 in. and a width of 4 in. They are designed to act as a…

A: let the density of the A-36 steels bars  are  ;ρ=7.85×103 kg/m3 ;   -------From standard valueE=200…

Q: Determine the magnitude of the horizontal force F and the support reactions at pin A.If the cord CB…

A:

Q: 1) Rod AB is used to support block C having amassof 12kg.Determire the reaction at the smooth point…

A: Given, Mass of block C = m = 12 kg Hence, weight of block C = WC = mg = 12 x 9.81 = 117.72 N   There…

Q: s00 Ib- 8 ft U ZI

A:

Q: e bracket is held to the wall using three A-36 steel bolts at B, C, and D. Each bolt has a diameter…

A: Equate the sum of moments to zero about A. Here, FD is the force in bolt D, FC is the force in bolt…

Q: 1. A 65-millimeter diameter Am 1004-T61 magnesium cylinder is placed in the clamp at T, millimeter…

A: Given Data: Initial temperature, T1=20 C Final temperature, T2=130 C

Q: Q 5 -3 ft- -4 ft- C 4 ft PA

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.