6- The inlet conditions to a steam nozzle are 10 bar and 250°C. The exit pressure is 2 bar. Assuming isentropic expansion and negligible velocity, determine for 0.2 kg/s of steam: (i) The throat area. (ii) The exit velocity. (iii) The exit area of the nozzle. [Ans. (i) 1.44 cm2 ; (ii) 795 mls ; (iii) 2.15 cm2]

6- The inlet conditions to a steam nozzle are 10 bar and 250°C. The exit pressure is 2 bar. Assuming isentropic expansion and negligible velocity, determine for 0.2 kg/s of steam: (i) The throat area. (ii) The exit velocity. (iii) The exit area of the nozzle. [Ans. (i) 1.44 cm2 ; (ii) 795 mls ; (iii) 2.15 cm2]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

33 - Helium is compressed in a continuous flow compressor. The speed at the compressor outlet is 29 m/s, the cross-sectional area is 0.00123 m² and the specific volume is 0.9267 m³/kg. What is the mass flow rate? a) 0.03221 kg/h B) 0.04479 kg/h NS) 0.04188 kg/h D) 0.03849 kg/h TO) 0.03621 kg/h
39 - The speed of the air entering a nozzle at the nozzle exit was 196 m/s and its density was measured as 0.681 kg/m³. Since the mass flow rate in the nozzle is 1,421 kg/s continuously, which of the following is the outlet cross-sectional area of the nozzle? a) 48,325 cm² B) 49,373 cm² NS) 106,461 cm² D) 110,603 cm² TO) 84,678 cm²
8 A certain SSSF, adiabatic control volume with single inflow and outflow streams has mass-flow-rate, m(dot) = 7.5 kg/sec, and a specific entropy increase from inflow, to outflow, se-si= +1.6 kJ/(K * Kg). Determine dSnet / dt ( in kJ/(degrees Kelvin * sec)), which is the time-rate-of-change, net, of the entropy of the universe (control volume plus surroundings).
Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional area. At the last section of a jet engine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s at a pressure of 500 kPa and a temperature of 600 K enters a nozzle with an inlet cross-sectional area of 5 m2. The exit area of the nozzle is 20% of its inlet area. The air leaves the nozzle at a velocity of 300 m/s. The nozzle is not well-insulated and duringthis process, 5 kJ/kg heat is lost. (i) In analysing this nozzle using the 1st law of thermodynamics,the change in which type of energy is negligible? (ii) Determine the density and velocity of the air entering thenozzle. (iii) Calculate the density of the air as it leaves the nozzle.
It is proposed that a nozzle receive air at 2 m/s, 300 K, and 150 kPa, attemperature of 280 K, and a velocity of 100 m/s. The mass flow rate is 0.1 kg/s. The surface of the nozzle is kept at 270 K. Assuming that the air behaves as an ideal gas with constant specific heats. Is this process possible?Given: Vel1 = 2 m/s, T1 = 300 K, P1 = 150 kPa, Vel2 = 100 m/s, T2 = 280 K, P2 = 110 kPa, dm/dt = 0.1 kg/s, Cp,air = 1.005 kJ kg-1 K-1
Where necessary, assume air as an ideal gas and consider R = 287 J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). a) A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional area. At the last section of a jet engine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s at a pressure of 500 kPa and a temperature of 600 K enters a nozzle with an inlet cross-sectional area of 5 m2. The exit area of the nozzle is 20% of its inlet area. The air leaves the nozzle at a velocity of 300 m/s. The nozzle is not well-insulated and during this process, 5 kJ/kg heat is lost.Figure Q1.a: Schematic of a Jet engine.(iii) Calculate the density of the air as it leaves the nozzle.
Where necessary, assume air as an ideal gas and consider R = 287 J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). a) A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional area. At the last section of a jet engine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s at a pressure of 500 kPa and a temperature of 600 K enters a nozzle with an inlet cross-sectional area of 5 m2. The exit area of the nozzle is 20% of its inlet area. The air leaves the nozzle at a velocity of 300 m/s. The nozzle is not well-insulated and during this process, 5 kJ/kg heat is lost. Figure Q1.a: Schematic of a Jet engine.(ii) Determine the density and velocity of the air entering thenozzle.
Where necessary, assume air as an ideal gas and consider R = 287 J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). a) A nozzle is a device that is used to increase the velocity of a fluid by varying the cross-sectional area. At the last section of a jet engine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s at a pressure of 500 kPa and a temperature of 600 K enters a nozzle with an inlet cross-sectional area of 5 m2. The exit area of the nozzle is 20% of its inlet area. The air leaves the nozzle at a velocity of 300 m/s. The nozzle is not well-insulated and during this process, 5 kJ/kg heat is lost.Figure Q1.a: Schematic of a Jet engine. (i) In analysing this nozzle using the 1st law of thermodynamics, the change in which type of energy is negligible?
11Air gas expands isentropically through a converging nozzle from a large tank at 160 lbf/in2, 600°R, and discharges into a region at 50 lbf/in2. The exit flow area is 1 in2. For air, use Cp = 0.24 Btu/lb.R. a. Determine the pressure at the exit in lbf/in2 b. Determine the mass flow rate through the nozzle, in lb/s
Q5/ A surface condenser handles condensate at 70.15 cm Hg when barometer reads 76 cm Hg. Steam entering at 2360 kg/hr requires cooling water at 6.81  102 kg/hr, 10°C. Cooling water leaves condenser at 27.8°C while condenser has mean temperature of 37°C. Air leaks into condenser at 0.3 kg/min. Determine, (i) the mass of vapour going out with air per hour (ii) the state of steam entering.
Consider an aircraft engine operating at subsonic conditions with a nozzle that has an exit area of 142in2 and a nozzle inlet/exit area ratio of 2. Engine gases flowing at 30lbm/s enter the nozzle with a pressure of 0.83 bar and avelocity of 144 m/s. The gases expand through the nozzle, exiting at the ambient pressure of 7.25 psia with a velocity of 1320 ft/s. a) For these conditions, what is the force (in units of lbf) trasmitted to the structure holding the nozzle. Provide both direction and magnitude of the force. b) Based on your results, comment on whether the force acting on the nozzle would hlep speed up or slow down a vehicle that used this nozzle as part of a jet propulsion system. I mostly wanted help in part b. Thank you.
Bottom part only please, Discuss why the petrol engine is irreversible in terms of entropy and work lost due to the spontaneous flow of heat resulting from finite temperature differences.