6- Write the composition of thermocouple?

Q: 10- The hook law is

A: To explain: The Hook's law. Explanation: If the force is applied to the material, then the material…

Q: Calculate the absolute permeability of the core.

A: Question 1 Given: Radius (R) = 2.54×10-2 mLength (L) = 0.3 mFlow rate q =1×10-6 m3/sDifferential…

Q: What is propose of riser designed

A: To explain the purpose of riser design.

Q: Determine optimum velocity ?

A: Given: Rotor diameter,d=9 mSpeed,N=2700 rpmNozzle angle,α=300Optimum velocity:    It is defined as…

Q: What happens at the eutectic point?

A: Eutectic point is the point in the phase diagram where the temperature of the liquid phase of the…

Q: ynami

A: given: what is second law of thermo dynamic?

Q: What is the major advantage of the pulse-jet method ?

A: The major advantage of the pulse jet method is

Q: Which of the following heat treatment

A: Given; Following are the heat treatment process used for surface hardening of steels: Where,Heat…

Q: What is the final gas pressure?

A: Final gas pressure need to find.

Q: 3. Explain about pipeline pigging?

A: Solution:   Pigging in Pipeline is explained below:

Q: DESCRIBE THE PROCESSES AND CYCLES?

A: Consider the PV diagram shown below for a process and cycle.

Q: Draw the Ts diagram of the whole process

A:

Q: intercooling pressure for minimum

A: Given; The compressor of a gas turbine plant, operating on an idealintercooled Brayton cycle…

Q: ospneric pressure, an inlet pressure of 10 atm is required. a. What is the permeability? b. If we…

A:

Q: The thermocouplê coul for temperature measun reference point is define point is: Select one:

A: The Thermocouple

Q: question 3 above is c hat is the final tem v of the steam in this

A: Given data P1 = 2800 kPa P2 = 4700 kPa T = 390 degree C Specific enthlpy, specific volume and…

Q: Glass or plastic core

A: Length,L = 20 km = 20,000 m n1 = 1.59n2 = 1.58

Q: What is a bus section in the electrostatic precipitator?

A: ELECTROSTATIC PRECIPITATOR - An ESP is a filter less air cleaning device that is use to capture the…

Q: -K-Type thermocouples were placed at multiple locations along the copper rods to mesure temperature.…

A: The thermocouple working rule is based on the Seeback Impact. This impact states that when a…

Q: What is the purpose of reheating steam in the reheat cycle?

A: Reheating is a process in which expansion of steam takes place in multiple stages or multiple…

Q: 7. What is the value of latent heat at the critical point?

A: Given :-  What is the value of latent heat at critical point ?   Latent heat :-  The latent heat is…

Q: State an equation of vertical pressure in uniformly loaded rectangualr area ?

A: given:   State an equation of vertical pressure in uniformly loaded rectangualr area ?

Q: average power consumption

A: Given;    cast iron  block of ,length=200 mmdepth of cut=4 mmfeed=0.25 mm/ strokecutting edge angle,…

Q: What is lower explosive limit in thermal oxidiser?

A: Many process and manufacturing industries are having to install “thermal oxidisers” (Incinerators or…

Q: What is energy release rate and the relationship with stress intensity factor?

A:

Q: A- What is meant by the term superheat?.

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: Define Constant Specific Heats (Approximate Analysis)

A: In constant specific heat assumption, the specific heat is assumed to be constant at some average…

Q: How is high efficiency accomplished in an airconditioningcondensing unit?

A: The Seasonal Energy Efficiency Ratio, or SEER, is a rating system that measures the maximum…

Q: State any 15 Advantages of FBC Boiler also give one line explanation of every advantage you state.

A: Introduction: In India, the majority of the coal that is accessible is of poor quality, has a high…

Q: (b) State THREE (3) differences between cold working and hot working processes.

A: Deformation of the material will be done at a temperature less than recrystallization temperature is…

Q: What is the strength of the Vortex sheet ?

A: In fluid mechanics, the vertex sheet is a term that is used for the discontinuity in the velocity of…

Q: 1-why the heat exchanger are produce from stainless-steel? 2-what are the differentiation between…

A: Answer 1: The primary function of the heat exchangers is exchange the heat from hotter fluid to the…

Q: What is chilled and condenser treatment process?

A: A chiller is a mechanical system used for the purpose of refrigeration in industries. It helps in…

Q: efficiency and pres Explain each of the processes on the T-s diagram.

A: Given: Gas turbine cycle Describe the processes.

Q: Write down details about Cooling Tower's working principle, components and description with diagrams

A: Cooling towers are devices used to reduce the temperature of hot water streams. They are a special…

Q: Problem # 7. A 25,000 sq ft w.t. boiler produces 320,000 lb per hour steam at 350 psig, 750 °F from…

A: Given data, The rate of steam output, m˙s = 320000 lb/hr Pressure and temperature of the output…

Q: At the end of the process, which one of the following situations will be true?

A: Given; In the figure shown,System is a pure substance kept in a piston-cylinder arrangement.System…

Q: An air conditioning supply fan is operating at and requiring 4.85kW. 600 RPM against is delivering…

A: Given:Old speed = 600 rpmP = 500 PaPower = 4.85 kWVolume,ν = 540 m3minv'=610 m3min Assuming

Q: ccupants and infiltration, but excluding intentional ventila ost nearly the room sensible heat…

A: Answer is given below

Q: 5. The temperature of the hard soldering or silver brazing is 842F°. (a) above (b) equal (c) under

A: The temperature of the hard soldering or silver brazing is about 1145°F to 1650°F

Q: Explain the principle behind indirect fired heater ?

A: Fired heater: Fire heaters can be understood as furnaces. It is used to heat gases or liquids to the…

Q: nt of 660°C.... 80°C at wh

A: solution of above problem is below:

Q: maximum possible reduction

A: Given: A thick slab is being cold rolled using roll of: Diameter(d)=600mm R=300 mm Coefficient of…

Q: ht, what is the tension in the wire?

A: To find tension ( T)

Q: What's the Cv for air at 30 to 60℃?

A: The value of  Cv for air at 30 to 60℃ Cv= 0.718 KJ/kg-K as value of Cp = 1.007 KJ/kg-k