6. A box is on a ramp inclined at 25° to the horizontal. The coefficient of static friction is .30, and of kinetic friction .20. M₂=30 Me=20m a. The box slides down the ramp. b. The box stays on the ramp without slipping. c. The box first slips, but then stays fixed after slowing down. d. We need the mass of the box to answer the question. 3250 w th mg OL 7 = MgCOSTS

6. A box is on a ramp inclined at 25° to the horizontal. The coefficient of static friction is .30, and of kinetic friction .20. M₂=30 Me=20m a. The box slides down the ramp. b. The box stays on the ramp without slipping. c. The box first slips, but then stays fixed after slowing down. d. We need the mass of the box to answer the question. 3250 w th mg OL 7 = MgCOSTS

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter4: Newton's Laws Of Motion

Section: Chapter Questions

Problem 79AP: A box rests on the back of a truck. The coefficient of static friction between the box and the bed...

See similar textbooks

Similar questions

If you wish to reduce the stress (which related to centripetal force) on high-speed tires, would you use large- or small diameter tires? Explain.
A 125 kg box is pushed up a ramp with a force of 100N applied at a 30 deg below the horizontal. Coefficient of static friction is 0.9. 1. What is the normal force on the box? 2. What is the friction force on the box? 3. What is the largest friction force could be?
A 1.5 kg block is connected by a rope across a 50-cm-diameter, 2.0 kg pulley, as shown. There is no friction in the axle, but there is friction between the rope and the pulley; the rope doesn’t slip. The weight is accelerating upward at 1.2 m/s2. What is the tension in the rope on the right side of the pulley?
A 120 N iron ball rests on a 20° smooth incline. What is the tension in the rope, hung at 40° below horizontal, which prevents the ball from sliding or rolling down the incline?a. 44N b. 50N c. 54N d. 60N
Suppose you have a 120-kg wooden crate resting on a wood floor. (a) What maximum force can you exert horizontally on the crate without moving it? (b) If you continue to exert this force once the crate starts to slip, what will the magnitude of its acceleration then be?
A 0.400-kg pendulum bob passes through the lowest part of its path at a speed of 3.00 m/s. (a) What is the tension in the pendulum cable at this point if the pendulum is 80.0 cm long? (b) When the pendulum reaches its highest point, what angle does the cable make with the vertical? (c) What is the tension in the pendulum cable when the pendulum reaches its highest point?
In the Atwood machine discussed in Example 5.9 and shown in Figure 5.14a, m1 = 2.00 kg and m2 = 7.00 kg. The masses of the pulley and string are negligible by comparison. The pulley turns without friction, and the siring does not stretch. The lighter object is released with a sharp push that sets it into motion at i = 2.40 m/s downward. (a) How far will m1, descend below its initial level? (b) Find the velocity of m1 after 1.80 s.
(a) If half of the weight of a small 1.00103 kg utility truck is supported by its two drive wheels, what is the magnitude of the maximum acceleration it can achieve on dry concrete? (b) Will a metal cabinet lying on the wooden bed of the truck slip if it accelerates at this rate? (c) Solve both problems assuming the truck has four-wheel drive.
A steel ball is dropped onto a hard floor from a height of 1.50 m and rebounds to a height of 1.45 m. (a) Calculate its velocity just before it strikes the floor. (b) Calculate its velocity just after it leaves the floor on its way back up. (c) Calculate its acceleration during contact with the floor if that contact lasts (8.00105s). (d) How much did the ball compress during its collision with the floor, assuming the floor is absolutely rigid?
The board sandwiched between two other boards in Figure P5.97 weighs 95.5 N. If the coefficient of static friction between the boards is 0.663, what must be the magnitude of the compression forces (assumed horizontal) acting on both sides of the center board to keep it from slipping?
Ina traction setup a broken bone, with pulleys and rope available, how might we be able to Increase the force along the tibia using the weight? (See Figure 4.30) (Note that the tibia is the shin bone shown in this image.) Figure 4.30 A leg is suspended by a traction system in which wires used to transmit forces. Frictionless pulleys crw.ge the direction of the force T without changing Its magnitude.
This problem returns to the tightrope walker studied in Example 4.6, who created a tension of 3.94103 N in a wire making an angle 5.0° below the horizontal with each supporting pole. Calculate how much this tension stretches the steel wire if it was originally 15 m long and 0.50 cm in diameter.