6. A flat plate 200 mm x 750 mm slides on oil (μ = 0.85 Pa.s) over a large plane surface as shown in the figure. What force F is required to drag the plate at a velocity v of 1.2 m/s if the thickness t of the separating oil film is 0.6 mm. a. 170 N b. 1700 N c. 255 N Oil SZERBANK*XXXXX d. 2.5 Plate F. V

6. A flat plate 200 mm x 750 mm slides on oil (μ = 0.85 Pa.s) over a large plane surface as shown in the figure. What force F is required to drag the plate at a velocity v of 1.2 m/s if the thickness t of the separating oil film is 0.6 mm. a. 170 N b. 1700 N c. 255 N Oil SZERBANK*XXXXX d. 2.5 Plate F. V

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the value of the deflection at point B due to concentrated load P in the form ??=??????????? Note: EI will cancel out in further calculations. Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
Determine the resultant of the vertical thrusts on the sphere shown in the figure for the data: d=0.6m; R=0.5m;h=4m.
Determine the volume V and total surface area A of the solid generated by revolving the area shown through 180° about the z-axis.Help
A stone is thrown vertically upward with a velocity of 40 feet per second from the top of a tower 200 feet high. When will it strike the ground? (hint: take a= -32 and s=0, v=40, when t=0. Consider the height of the tower to be negative.)
A block weighing 100Nis held on a 40 ̊incline by a bar attached to a 150N block on a horizontal plane. The bar, which is fastened by smooth pins at each end, is inclined 20 ̊above the horizontal. The angle of friction between each block and its plane is 18 ̊. Fin the horizontal force P applied to the 150N block which will cause to be on the point of moving (a) to the right; (b) to the left.
The winch in the figure is used to move the 135kg uniform log. The coefficient of static friction between the log and the plane is 0.40. Which of the following most nearly gives the value of T for impending sliding?
A block weighing 100 N is placed on an inclined plane of slope angle 30 degrees and is connected to a secondhanging block of weight “W”, by a cord passing over a small frictionless pulley. The coefficient of slidingfriction is 0.3. Find the weight “W” for which the 100N block moves up the inclined plane at a constantvelocity.
Assume g=10 m/s2
The blocks shown are separated by a solid strut which is attached to the blocks with frictionless pins. If the coefficient of friction for all surfaces is 0.25, determine the value of the horizontal force P to cause motion to impend to the right.
There is a conical plug at the bottom of the pressure tank as seen in the figure. The air pressure is 50 kPa and the specific gravity of the fluid in the tank is 27 kN/m3 'kind. remaining in the tank Determine the direction and magnitude of the force acting on the cone curve surface (h1=1 m, h2=3 m, ɵ=60o )
A block of mass m = 2.00 kg rests on the left edge of a block of larger mass M = 8.00 kg. Thecoefficient of kinetic friction between the two blocks is 0.300, and the surface on which the 8.00-kgblock rests is frictionless. A constant horizontal force of magnitude F = 10.0 N is applied to the2.00-kg block, setting it in motion as shown in Figure P5.65a. If the length L that the leading edgeof the smaller block travels on the larger block is 3.00 m, (a) how long will it take before this blockmakes it to the right side of the 8.00-kg block, as shown in Figure 3? (Note: Both blocks are set inmotion when F is applied.) (b) How far does the 8.00-kg block move in the process?
A boy slides down a water chute starting from rest at A. Neglecting friction. a. which of the following gives the velocity at the end of the chute at B in ft/s. b. which of the following gives the velocity on entering the water at C in ft/s. C. which of the following gives the horizontal distance of C from B in miles.