6. Cables AB, AC, and AD hold the balloon in the position shown. If the balloon exerts an upward force of 5000 N at the point of concurrency of the three cables, find the magnitudes of the tensile forces on the three cables TAn, TAC, and TAD. Hint: The resultant of the cable tensions is force exerted by the balloon at point A but opposite in direction. 560 m 4.20 m 3.30 m 4 20 m 2.40 m y

6. Cables AB, AC, and AD hold the balloon in the position shown. If the balloon exerts an upward force of 5000 N at the point of concurrency of the three cables, find the magnitudes of the tensile forces on the three cables TAn, TAC, and TAD. Hint: The resultant of the cable tensions is force exerted by the balloon at point A but opposite in direction. 560 m 4.20 m 3.30 m 4 20 m 2.40 m y

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

13. A 12-m pole supports a horizontal cable CD and is held by a ball and socket at A and two cables BE and BF as shown in Figure 2. Knowing that the tension in cable CD is 14 KN and assuming that CD is parallel to the x-axis (0), determine the horizontal component of the reaction at A. A. 7.00 kN B. 17.50 kN C. 22.4 kN D. 2.50 kN
Determine the angle ø (0°≤ø≤90°) between cables BA and BC so that 500N vertical force has a component of 250N which acts along cable CB, from C to B. Set angle = 60°
Given that mA=16.2kg,mB=105.7kg,μs=0.39,μk=0.3,θ=60.3deg, (use gravity as 9.81m/s^2) What is the magnitude of the normal force on mass A? What would be the tension in the cable if the blocks were not moving? What is the maximum Tension force that could be applied before block A would start moving? What is the absolute value of the ratio of accelerations for block A and block B? |aBaA|= What is the I^ (global X direction positive to the right) component of the acceleration of block A? What is the J^ (global Y direction positive to up) component of the acceleration of block A? What is the I^ (global X direction positive to the right) component of the acceleration of block B? What is the J^ (global Y direction positive to up) component of the acceleration of block B?
In Prob. 3.59, determine the perpendicular distance between cable AE and the line joining points D and B.(Reference to Problem 3.59):The triangular plate ABC is supported by ball-and-socket joints at B and D and is held in the position shown by cables AE and CF . If the force exerted by cable AE at A is 55 N, determine the moment of that force about the line joining points D and B.
In this Question the cable attached to a tower as you can see a) Since f1 = 8m and f2 = 8m, find the horizontal and vertical components of the force on point C of the tower. b)Since f1 = 8m, what must f2 be in order for the horizontal component of the force to point C of the tower to be zero?
Consider the three-dimensional structure shown in the figure, fixed to the ground at point O, and restrained by cables AB and CD. The tension TT in the restraining cable CD is 2.8 kN. Calculate the magnitude of the vector moment (in kNm) produced by the force exerted by the cable CD on point C, about the point O (assume use of the right-hand rule). Take aa = 4.7 metres, and bb = 3.8 metres.
The cables in Figure P6.7 have been dimensioned so that a 3-kip tension force develops in each vertical strand when the main cables are tensioned. What value of jacking force T must be applied at supports B and C to tension the system?
A crane is oriented so that the end of the 25-m boom AO lies in the yz plane. At the instant shown, the tension in cable AB is 4 kN. Determine the moment about each of the coordinate axes of the force exerted on A by cable AB.
B. At A, a 90-kg container begins at rest. When the cable is exposed to a continuous force of F-450N, determine its speed when it reaches point B. Also, what is the constant force if the speed of crate A is 7.5 m/s when passing through crate B? Neglect friction and the size of the pulley.
The cables are used to tether a balloon as shown. Determine the vertical force P exerted by the balloon at A knowing that the tension in cable AD is 481N.
Two blocks A and B have a mass of 10 kg and 100 kg, respectively. Block B is released from rest. Give the tension in the cable, the equation with corrected sign, acceleration of block A.
The horizontal boom OC, which is supported by a ball-and-socket joint and two cables, carries the vertical force P = 8 kN. Neglect the weight of the boom. 1. Which of the following most nearly gives the tension in cable AD in kN? a. 12.77 b. 15.66 c. 18.61 d. 9.150 2. Which of the following most nearly gives the tension in cable CE in kN? a. 4.512 b. 7.01 c. 8.91 d. 3.51 3. Which of the following most nearly gives the reaction at point O in kN.? a. 6.32 b. 5.81 c. 14.71 d. 13.96