6. Design a clamp coupling for transmitting 36 kW, at 200 rpm. Allowable shear stress in shaft is 45 MPa, allowable shear stress in key is 40 MPa, and allowable crushing stress in key is 90 MPa. The number of bolts joining the two halves is 4. The permissible tensile stress in bolts is 60 MPa. The coefficient of friction between the muff and shaft can be taken as 0.25

6. Design a clamp coupling for transmitting 36 kW, at 200 rpm. Allowable shear stress in shaft is 45 MPa, allowable shear stress in key is 40 MPa, and allowable crushing stress in key is 90 MPa. The number of bolts joining the two halves is 4. The permissible tensile stress in bolts is 60 MPa. The coefficient of friction between the muff and shaft can be taken as 0.25

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.76P: The clutch described in Prob. 7.75 is to transmit a torque of 120lbft when the total spring force...

See similar textbooks

Similar questions

Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
The clutch described in Prob. 7.75 is to transmit a torque of 120lbft when the total spring force exerted on the pressure plate is 75 lb. If Ri=4in., calculate the minimum acceptable value for RO. Assume that the clutch is new.
8. Design a clamp coupling for transmitting 25 kW at 300 rpm. Allowable shear stresses in shaft and key are 50 MPa and 45 MPa, respectively. The number of bolts joining the two halves of muff is 4. The permissible tensile stress in the bolt is 70 MPa and the permissible crushing stress in the key is 90 MPa. The coeffi cient of friction between the muff of the CI and the shaft of steel is 0.20.
A cone clutch has cone elements at an angle of 12o. The clutch transmit 25 HP at a speed of 1200 rpm. The mean diameter of the conical friction section is 16 in and the coefficient of friction is 0.35. Find the axial force needed to engage the clutch.
A 600 mm steel pulley transmits 50 kW at 900 rpm. The arc of contact between the belt and pulley is 144 degrees, the coefficient of friction between belt and pulley is 0.3 and the safe working stress of the belt is 2750 kPa. Find the width of the belt used if the thickness is equal to 12 mm.
Design a clamp coupling to transmit ‘35’ kW at ‘120’ r.p.m. The allowable shear stress for the shaft and key is ‘50’ MPa and the number of bolts connecting the two halves are six. The permissible tensile stress for the bolts is ‘70’ MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3.
3. Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the shaft and key is 40 MPa and the number of bolts connecting the two halves are 4. The permissible tensile stress for the bolts material is 70 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
The coefficient of friction of a disk clutch with two pairs of contact surfaces is 0.25. The maximum pressure under working conditions is 220kPa only. The clutch is used to connect two 25mm solid shafts with allowable shearing stress of 69 MPa. The inner and outer diameter of the clutch face is 60 mm and 120mm, respectively. What is the power in kW transmitted at 1000 rpm?
A pullev 615 mm in diameter transmits 40 kW at 630 rpm The arc of contact between the belt and the pulley is 140 degrees, the coefficient of friction between the belt and the pulley is 0.30, and the safe working stress of the belt is 2.0 MPa. Calculate the effective belt pull
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
A single plate friction clutch with both sides of plate being effective is used to transmit power at an engine speed of 200rpm. It has outer and inner radii 10cm and 8cm respectively. Find maximum power transmitted and the corresponding axial thrust, if the maximum intensity of pressure is not to exceed 0.08N/mm2 . Assume coefficient of friction as 0.25.