Pravinbhai End A of the uniform 14-kg bar is pinned freely to the collar, which has an acceleration a = 4.3 m/s² along the fixed horizontal shaft. Ifthe bar has a clockwise angular velocity w = 1.9 rad/s as it swings past the vertical, determine the components of the force on the bar atA for this instant. Ax is positive if to the right, negative if to the left. Ay is positive if up, negative if down.AOaT1.4 mAnswers:Ax =Ay =iiNN

Answered: Image /qna-images/answer/73b85d8b-3464-4887-bb48-b11f9abd4790.jpg

Answered: End A of the uniform 14-kg bar is…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 0.2-Kg pin P is constrained to move in the smooth curved slot. Which is defined by the lemniscate r = (0.6cos 2theta) m. Its motion is controlled by the rotation of the slotted arm OA, which has a constant clockwise angular velocity of dot theta =-3 rad/s . Determine (a)-the force arm OA exerts on the pin P when theta = 0 ^ 0 ,note that the motion is in the vertical plane, (b) the acceleration in the r and 0 direction. r = (0.0cos 2theta) m 4
Rod AB and body C each have a mass m. The system is released from rest when 00. Determine the distance x which will result in the maximum angular ac- celeration of rod AB and the resulting angular acceleration when 0 = 30º. (Draw FBDs)
The trailer has a mass of 400kg and the mass center at G. is being pulled by a horizontal force of magnitude of F = 800N. Determine the acceleration of the trailer, as well as the normal forces (Na and Nb) on the pair of wheels at A and B respectively. Assume the wheels are free to roll and have negligible mass.
The 12-kg slender rod is pinned to a small roller A that slides freely along the slot. If the rod is released from rest at f) = 0°, determine the angular acceleration of the rod and the acceleration of the roller immediately after the release.
The 0.75-lb smooth can is guided along thecircular path using the arm guide. If the arm has anangular velocity θ’= 2 rad./s, and an angular acceleration θ’’= 0.4 rad./s2, at the instantθ= 30°, determine the force ofthe guide on the can. Motion occurs in the horizontal plane.
If P = 30 lb, determine the angular acceleration of the 50-lb roller. Assume the roller to be a uniform cylinder and that no slipping occurs
In the figure, rod AB has a mass of 10 kg, and must slide within the slots as shown. If the spring is unstretched when θ = 0°, determine the angular velocity of the bar when it reaches that angle after being released from θ = 30°.
At the instant shown, the 200-lb bar rotates clockwise at 4 rad/s. The spring attached to its endalways remains vertical due to the roller guide at C. If the spring has an unstretched length of 2ft and a stiffness of k = 9 lb/ft, determine the angular velocity of the bar the instant it has rotated 39° clockwise.
The uniform thin pole has a weight of 50 N and a length of 26m. If it is placed against the rough wall and on the rough box in the position d = 10 m, µs = 0.3 at points A, B and C P= 150 NBox weight = 100 N Determine the distance x when the motion of the pole impend
If the cord at B suddenly fails, determine a) The angular acceleration of the beam. b) The horizontal and vertical components of the initial reaction at pin A. The beam has a mass of 50 kg. Treat the beam as a uniform slender rod.
The vertical bar AB has a mass of 150 kg with center of mass G midway between the ends. The bar is elevated from rest at θ = 0 by means of the parallel links of negligible mass, with a constant couple M = 5 kN∙m applied to the lower link at C. Determine the angular acceleration α of the links as a function of θ and find the force B in the link DB at the instant when θ = 30°.
If the cord is subjected to a horizontal force of P = 150 N, and gear is supported by a fixed pin at O,determine the angular velocity of the gear and the velocity of the 20-kg gear rack in 4 s, starting from rest. The mass of the gear is 50 kg and it has a radius of gyration of k0 = 125 mm. Assume that the contact surface between the gear rack and the horizontal plane is smooth.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS