6. Determine the output for the circuit with components R = 1 MQ, R₁ = 100 k, R₂ = 50 kn, and R3 = 500 KQ. ANS. -20(V2-V1)

Q: A current of 100 mA is applied to a 15 µF capacitor which has an initial voltage across it of 25…

A:

Q: A unity feedback system has the open loop transfer function shown bel Find the angle of departure.…

A: In this question We need to determine the angle of departure angle of the given system.  We know…

Q: 1) Find the phasor representations of a. v()--170 sin(2760/ -60°) V V = -170 w t60 Q = -60° b. v(t)…

A:

Q: 2. A facility manager replaces all the TS lights in an office when they have reached 80% of their…

A: Group re-lamping: It is process in which all the old lights are replaced by new ones on…

Q: Calculate the active power P, reactive power Q, apparent power S and it's phase-shift angle p. Give…

A:

Q: L = ?

A: Given- Source voltage- vt=212.2sin500t VVR=120 V To Find- The value of inductor L.

Q: Q4. An RLC circuit is given in Figure 4. If the values of L = 0.25 H, R = 100, and C = 100 µF, and…

A:

Q: 24. (EE352) Consider the following circuit. For the nFET, assume Vtn=+1V and What is the DC voltage,…

A: We need to find out source voltage for given MOSFET circuit .

Q: What is a good characteristic impedance for microstrip transmission line?

A: We need to explain characteristic impedance for microstrip transmission line.

Q: For the circuit shown, determine the equivalent voltage source in Volts where I=8 A, and R=24 2.…

A: In this question We need to determine the equivalent voltage source.  We know Voltage across the…

Q: 5. The air handling unit for an office has a 20 HP motor that operates at full speed. An energy…

A:

Q: 1602 is (↑) Ω 20 Ω www XIA + 40 mi 80 ΩΣ 40 ΩΣ a b

A: Here given, is=8 Ax=120  In the circuit a dependent source is present it is asked to find the…

Q: What is fractionally spaced equalizer? Discuss in detail about the function of fractionally spaced…

A: A digital filter is used by the fractionally spaced equaliser to equalise the channel response and…

Q: A 20KVA, 2200/220 V, 50 Hz single phase transformer has the below parameters HV:r-2.492.X-652 LV:…

A: Given : V1=20 kVAV1=2200 VV2=220 V

Q: 10.7 Z(s) is p.r. Determine min [Re Z(jw)] and synthesize Z(s) by first removing min [Re Z(jw)]. 253…

A:

Q: Determine Vb for the following circuit using superposition when V1=15 V, V2=6 V, R1=1,000 ,…

A: In this question We need to determine the voltage Vo  using the super position theorem.  Here two…

Q: What is the value of l2 in the network shown below? 8V 4V 10 V₁ 1₂ 16 V

A: Given circuit-   To find- The value of current I2 in the circuit.

Q: Significance of Tracking in control systems. Could an example with  temperature control for  a human…

A: It is asked to tell the significance of tracking in control systems. It is specified to show an…

Q: 2. Calculate the real and reactive power delivered by the single-phase source in the two…

A: The required parameters can be obtained by calculating the total impedance of the circuit and the…

Q: Use the defining equation for the DTFS coefficients to evaluate the DTFS representation of the…

A: The DTFS equation is given as: xdn=xdn+Nwhere, N=period It is known that, xdn=∑k=0N-1ckej2πknNwhere,…

Q: 2- In the circuit shown in fig (3), calculate the current through the resistor R when its resistor…

A:

Q: Determine Q-point for the diodes in the circuit given below using the constant voltage drop model…

A:

Q: Draw a bandpass filter, using a parallel resonant LC circuit plus a resistor. Use a center frequency…

A:

Q: USE NODAL ANALYSIS Given a = 2, b = 1, c = 1, d = 12, e= 24, f = 1 and g = 7.5, in the circuit…

A: here we have to solve for current I0 in the given circuit.

Q: Problem 2: In the circuit of the figure below, design the value of R2 for the output voltage to be…

A: We need to find out the unknown value of resistor for given circuit for given output voltage .

Q: What is the average value of the output of the half-wave rectified waveform shown? ^^^ s 100 V-

A: Calculation of average value of the output of the half wave rectifier waveform given: From the…

Q: two-bit ripple-carry adder with inputs A[1:0] and B[1:0] and an output C[1:0] using one-bit half and…

A: Two-bit input A= A1 A0 Two-bit input B= B1 B0 The output of ripple carry adder C = C2 C1 C0…

Q: Given the input signal and impulse response, find the output signal by evaluating the convolution…

A: Given: Input signal x(t) and impulse response h(t) as,  x(t)=u(t), h(t)=sinπt [u(t)-u(t-1)], To…

Q: 10. A facility has a power factor of 0.83 and would like to increase to 0.90 by installing a…

A: Given data  Power factor cos(phi1) =0.83 Required power factor cos(phi2) =0.9 Demand in facility P =…

Q: A series RIC circuit consisting of a 25 ohms resistor, 0.8 henry inductor, and a 8.8F capacitor is…

A: In these questions We need to determine the all unknown parameters.  We know Inductive Reactance XL…

Q: Plot the transfer characteristic of the circuit in Fig. P4.91 by evaluating v, corresponding to v =…

A:

Q: Explain how a closed-loop automatic washing machine might operat

A: We need to explain how a closed-loop automatic washing machine might operate.

Q: Question-2 Consider the following circuit, and given: lin(s) Iin (s) = 1) ↑ 2s-1 (s + 1)(s² +25) 400…

A:

Q: QF Consider a solar cell with a photocurrent of 25mA and a reverse saturation current of 3.66x10-11…

A: Given: I=3.66×10-11 AT=300 K

Q: Problem 4 the closed-loop characteristic equation 1 KG(s) = 0 The open-loop transfer function is…

A: Given Data: An open loop Transfer function, Gs=s2+4s+13 Considering the system as a unity-negative…

Q: Q\Two 3-phase, 6.6kW, star-connected alternators supply a load of 300kW at 0.8 pf lagging. The…

A: In this question we need to find the current, power factor, induced emf and load angle of each…

Q: 1. Consider the unity-feedback system with the open-loop transfer function: 10 s+1 Obtain the…

A: Answer: Given transfer function is  Gs=1s+5 Given that feedback in system is unity feedback.

Q: ssume that R4 is the load of the circuit, What is the power in R4 in Watts when =10 V, R1=100,…

A: We need to find out power dissipation in the given resistor for given circuit , so first we will…

Q: Question-1 Consider the following circuit, and given: Tout (s) = = Vin(t) Vin(t) = (-2e-* cos(5t) +…

A:

Q: What are coupled waveforms? Are they at either end of the same magnitude?

A: We need to define the coupled waveforms.Also, we have to explain whether the waveforms are at either…

Q: The closed loop gain of the system shown in the given figure is : 0.5

A: Given data, Open loop gain G = -3. Feedback factor H = 0.5. Block diagram is given as,

Q: Find lo using nodal analysis; Answer: Io = -3.86mA 6V 1+ www 6 ΚΩ I 6 ΚΩ 4 ΚΩ Το + 24V

A: Given data, The circuit is,

Q: Question 4 What is the rms value of current i(t) = Imcos(wt+0;)? O IM√2 O IM√3 O IM slash√2 O IM…

A:

Q: Q1. Under what conditions can we have V²A = -HoJ? Prove the identity.

A:

Q: If a voltage waveform has a peak voltage of 88.0V and 4.5% ripple, what is the minimum voltage

A: In this question we need to find the minimum voltage.

Q: For the circuit, the voltage drop for the red LED is 2 volts. (a) Find the voltage drop in Resistor…

A:

Q: V2 U-12V V U=1 V V3 U=12V + OP1 Vo

A: Here we have to find the voltage gain.

Q: 5. For this buffered circuit, sketch V.(t) by inspection: R₁ = 6 KQ; R₂ = 20 KQ; C = 10 µμF; Vc(0) =…

A: Given data,  R1=6Kohm. R2=20kohm . C=10uF. Vc(0)=9v. We have to find vc(t) (sketch) Circuit:

Q: A a Single phase 400W, 50 Hz motor takes Suply current of SOA at power factor of 0.6 Lagging The…

A:

Q: An iron ring has its mean length of flux path as 60 cm and its cross sectional area as 15 cm^2. Its…

A:

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.