6. The efficiency of DC to DC converter to drive de motor is --- than AC to DC Drivesa) lowerb) equale) higher7- The Four-quadrant operation of de motor can he implanted using --e) Semiconverter8. The supply froqueney of induction motor using frequency control is changed to -a) Full converterb) Dual convertera) abuve rated frequency. b) below rated frequency. e) Abuve and below rated frequency.9. The stable operation in torque- speed churacteristic for induction motor occur:e) at slip 05 to Sms10. The regenerative hraking for de to de convernter fed de motor would be effective if thea) between maximum slip and s0 h)at slip =1operating speed m :a) or tb) > uinc) thi

As per guidelines given to us ,we can only provide the solution of first question in multiple type…

6. The efficiency of DC to DC converter to drive de motor is than AC to DC Drives e) higher 7- The Four-quadrant operation of de motor can he implanted using -- a) lower b) equal e) Semiconverter 8. The supply frequeney of induction motor using frequency control is changed to - a) abuve rated frequency. b) below rated frequency. e) Abuve and below rated frequency. 9. The stable operation in torque- speed churacteristic for induction motor occur: e) at slip 05 to Sa 10, The regenerative hraking for de to de converter fed de motor would be effective if the a) Full converter b) Dual converter a) between maximum slip and s: b)at slip =1 operating speed n: a) o t b) >uan e) thi to tht

6. The efficiency of DC to DC converter to drive de motor is than AC to DC Drives e) higher 7- The Four-quadrant operation of de motor can he implanted using -- a) lower b) equal e) Semiconverter 8. The supply frequeney of induction motor using frequency control is changed to - a) abuve rated frequency. b) below rated frequency. e) Abuve and below rated frequency. 9. The stable operation in torque- speed churacteristic for induction motor occur: e) at slip 05 to Sa 10, The regenerative hraking for de to de converter fed de motor would be effective if the a) Full converter b) Dual converter a) between maximum slip and s: b)at slip =1 operating speed n: a) o t b) >uan e) thi to tht

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 3-phase, 4-pole induction motor drives a conveyor which needs a constant torque over its entire operating speed range. The per-phase rotor resistance referred to the stator side is 0.74 2. The motor is fed from a 3-phase inverter-based adjustable speed drive, with a volt per hertz control scheme. When the fundamental component of the inverter line output voltage is 400 V (rms), 50 Hz, the motor operates at its rated speed of 1470 rpm. The electromagnetic torque produced by the motor can be approximated as: (a) Estimate the rated mechanical power output and air-gap flux of the motor. (b) It is proposed to reduce the power consumption of the drive by operating at half of the rated speed. Estimate the required fundamental line voltage and frequency of the inverter (c) Assess the effect of the stator winding parameters on the air-gap flux found in Part(a)
Q5:- Adjust a fire angle for a three-phase fullwave semi-controlled converter to feed the separately exciter DC motor to get a load torque that can be reached to 730 rpm. When the supply voltage of converter is 160 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.
base on below mentioned Comparison of the performance indexes discuss and advice best induction motor.
analyze 3 commonly used ac motor starting methods using suitable diagrams and torque-speed curves
a. A three-phase, 220-V, 60-Hz induction motor runsat 1,140 r/min. Determine the number of poles (forminimum slip), the slip, and the frequency of therotor currents.b. To reduce the starting current, a three-phasesquirrel cage induction motor is started byreducing the line voltage to Vs/2. By what factorare the starting torque and the starting currentreduced?
A three-phase induction motor, operating at rated voltage and frequency, has a startingtorque of 1.35 times and a maximum torque of 2.2 times, both with respect to its rated-loadtorque. Ignoring the effects of the stator resistance and rotational losses and assumingconstant rotor resistance, determine the slip at the maximum torque;
- What are the main parts of an single phase induction motor?Explain the function of each. - Explain the function of Ballast and Starter in the discharge lamp?! - Can we connect a 10A load to domestic socket outlet? Justify your answer. - Which type of MCB is used in motor control and why this type of MCB is chosen over other types?
Describe the basic circuit of DC Generators including its yoke, fid windings, interpoles, fieldpoles, difference of shunt coils and series coils, commutator and brushes ?
The parameters of a three-phase, 50 Hz, 6-pole, 400 V star connected induction motor are r1 = 0.3 ohm, x1 = 0.5 ohm, r’2 = 0.15 ohm and x’2 = 0.2 ohm. The voltage and frequency of the induction motor is controlled by a power electronic converter (inverter). Calculate the required inverter output frequency and voltage to drive the induction motor load at 0.2 the rated speed of the motor and calculate the current drawn by the motor for that case. The formula for the maximum slip is given below:
B. What are differences in term of construction and working principle between Shaded Pole Induction Motor and Capacitor Start Induction Motor?
Write a summary (points) about the stator resistance test of the squirrel cage induction motor .
18. A single-phase, 120 V, 60 Hz, four-pole, split-phase induction motor has the following standstill impedances:Main winding: Zm =5+j6.25Auxiliary winding: Za =8+j6a) Determine the value of capacitance to be added in series with the auxiliary winding to obtain maximum starting torque.b) Compare the starting torques and starting current with and without the added capacitance in the auxiliary winding circuit when operated from a 120V, 60Hz supply.