6. Water is pumped to a storage tank from a pool by a centrifugal pump. The elevation difference between the pool and the storage tank is 60 m. The storage tank and the pool are open to atmosphere. 50 meters of 6 in Sc 40 steel pipe is used between pool and pump. After the pump 6 in Sc 40 pipe with a length of 22 m is suddenly contracted to 4 in Sc 40 pipe, that is 70 m. The flow rate of water is 2.5 m/min and the temperature is 20°C. If the pump efficiency is 0.6 and the cost of electrical energy is 0.40 TL/KWh,calculate daily cost of electricity used for this system. 2m +in Se 40 70m Open gate valve Storage tank 60m 22 m Pool 6 in Sc 40 Open gate valve 6 in Sc 40 50m pump

6. Water is pumped to a storage tank from a pool by a centrifugal pump. The elevation difference between the pool and the storage tank is 60 m. The storage tank and the pool are open to atmosphere. 50 meters of 6 in Sc 40 steel pipe is used between pool and pump. After the pump 6 in Sc 40 pipe with a length of 22 m is suddenly contracted to 4 in Sc 40 pipe, that is 70 m. The flow rate of water is 2.5 m/min and the temperature is 20°C. If the pump efficiency is 0.6 and the cost of electrical energy is 0.40 TL/KWh,calculate daily cost of electricity used for this system. 2m +in Se 40 70m Open gate valve Storage tank 60m 22 m Pool 6 in Sc 40 Open gate valve 6 in Sc 40 50m pump

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a hydroelectric plant the difference in elevation between the surfaace of the water at the intake and at the tailrace is 183m (600ft). When the flow is 80 cfs, the friction loss in the penstock is 60 ft and the head utilized by the turbine is 460 ft. The mechanical friction in the turbine is 100hp, and the leakage loss is 3 cfs. Find (a) hydraulic efficiency; (b) volumetric efficiency; (c) power delivered to shaft; (d) brake horse power, (e) mechanical efficiency; (f) over-all efficiency.
A fully-filled open storage tower of height 32 m and diameter 3.0m supplies water to a house. A horizontal pipe at the base of the tower has a diameter of 2.54cm. To satisfy the needs of the home, the supply pipe must be able to deliver water at a rate of 0.67 gal/s. a. If water were flowing at the maximum rate, what would be the pressure in the horizontal pipe?b. A smaller pipe, of diameter 1.27 cm supplies the second floor of the house, a distance of 7.2 m above the ground level. What are the flow speed and water pressure in this pipe?
At a hydraulic plant, the difference in elevation between the surface of the water at intake and at the tailrace is 180 m. When the flow is 2.5 cubic meter per second, the friction loss in the penstock is 15 meters and the head utilized by the turbine is 150 m. The mechanical friction in the turbine is 100 Hp, and the leakage loss is 3 cubic foot per second. Find the (a) hydraulic efficiency, (b) volumetric efficiency, (c) mechanical efficiency, and (d) power delivered to the shaft.
A centrifugal pump(efficiency 86%) lifts water through a total height of 42m from reservoir to discharge. Pumping is through 300m of 75mm diameter pipe at the rate of 20li/s. If pipe friction factor, f = 0.025, what KW is required? Answer: 9
A centrifugal pump pumps water at a flow rate of 7 m³/s to a height of 10 m. If the pump works at the best efficiency point, find the pump impeller diameter, pump speed, the best efficiency value of the pump, the head at the best efficiency value, and the specific speed of the pump, given that CQ=0.15 CH=6 CP=0.75.
A pump increases the pressure of water from 100 kPa to 900 kPa to an elevation of 35 m. The inlet and outlet diameters are identical. The net head of the pump is (a) 143 m (b) 117 m (c) 91 m (d) 70 m (e) 35 m
A four-stage centrifugal pump has four identical impellers, keyed to the same shaft. The shaft is running at 400 r.p.m. and the total manometric head developed by the multistage pump is 40m. The discharge through the pump is 0.2 m*3/s. The vanes of each impeller are having outlet angle as 45°. If the width and diameter of each impeller at outlet is 5cm and 60 cm respectively, Find the manometric efficiency.
A pump rated at 65% efficiency is used to transport water from a large open reservoir to a point 10m above at a rate of 450 L/min, into a vented tank. Assuming friction is negligible and that the efficiency of the motor is 77%, how much electricity is required to keep the process running for 24 hours? Choices: A. 29.37 kWh B. 35.28 kWh C. 56.71 kWh D. 43.21 kWh
In a pumping system handling water, the surface level of water in the open sanction tank is 3m below the pump centerline and the surface level in the tank is 23m above the pump centerline. The inlet piping ia 7.62cm in diameter has an equivalent of 26m of steel pipe. The discharge line is 6.35cm in diameter has an equivalent lenght of 72m. The pump discharge rate is 12.6 L/s. the friction factor to be 0.024 for both inlet and discharge pipes. Determine: The total head loss due to friction (HL=hfs+hfd) in meters 21.955 3.187 25.142 The total dynamic head in meters 51.142 45.955 49.142 The water power in kW 5.678 6.072 6.319
A Francis turbine rotates at 1600 rpm and a flow rate of 1 m3/sec enters it. The inlet and outlet diameters are 1.2 m and 0.55 m, respectively, and the corresponding sections between the blades are 0.24 m2 and 0.08 m2. The outlet angle of the water from the distributor is 10º, the outlet angle of the wheel b2 = 40º and the manometric efficiency of the turbine is 78%.Determine:a) The net jumpb) The torque and power on the shaft
A sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.85 L/s, with an output pressure of 3.05 × 105 Pa. a. The water enters a hose with a 2.8 cm inside diameter and rises 2.4 m above the pump. What is its pressure at this point, in pascals? You may neglect frictional losses. ( dont forget to convert the diameters of pipes into meters.) b. The hose then goes over the foundation wall, losing 0.35 m in height, and widens to 4.4 cm in diameter. What is the pressure now, in pascals? You may neglect frictional losses. ( dont forget to convert the diameters of pipes into meters.) Note: answer iS NOT 3.29 x 10^5 for either of these.
A pump at 65% efficiency is used to transport water from a large open reservoir to a point 10m above at a rate of 450 L/min, into a vented tank. Assuming friction is negligible and that the efficiency of the motor is 77%, determine electricity required to keep the process running for 24 hours.