6.11. Water flows at low speed V₁ through a circular tube with inside diameter d₁. A smoothly contoured body of diameter d₂ is held in the end of the tube where the water discharges to atmosphere. Neglect frictional effects and assume uniform velocity profiles at each section. Determine the pressure measured by gage and the force required to hold the body.

6.11. Water flows at low speed V₁ through a circular tube with inside diameter d₁. A smoothly contoured body of diameter d₂ is held in the end of the tube where the water discharges to atmosphere. Neglect frictional effects and assume uniform velocity profiles at each section. Determine the pressure measured by gage and the force required to hold the body.

Name: Please don't provide handwritten solution ..... 6.11. Water flows at l
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Please don't provide handwritten solution ..... 6.11. Water flows at low speed V₁ through a circular tube with inside diameter d₁. A smoothly contouredbody of diameter d₂ is held in the end of the tube where the water discharges to atmosphere. Neglec

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A nozzle that discharges a 60-mm-diameter water jet into the air is on the right end of a horizontal 120-mm- diameter pipe. In the line, the water has a velocity of 4 m/s and a gage pressure of 400 kPa. Find the magnitude and direction of the resultant axial force the water exerts on the nozzle and the head loss in the nozzle.
A fire pump delivers water through a 150 mm main to a hydrant to which is connected a 75 mm hose, terminating in a 25 mm nozzle. The nozzle is 3 m above the hydrant and 18 m above the pump. Assuming a total frictional loss of 18.5 m from the pump to the base of the nozzle, and a loss in the nozzle of 10 per cent of the velocity head in the jet, and neglecting air resistance, what gage pressure at the pump is necessary to throw a stream 30 m vertically above the nozzle?
A nozzle of diameter 20 mm at one end is used to eject water with a 20 m/s of designed velocity. What should be diameter of the nozzle at the wide end if the velocity at this end is 10 m/s.
A straight horizontal pipe 100 mm in diameter terminates in a short, tapering nozzle from which a jet of water 50 mm in diameter is discharged to atmosphere. If the gauge pressure immediately before the nozzle is 50 kPa and friction in the nozzle is negligible, calculate the tensile force between the nozzle and pipe.
If the velocity in a 300-mm pipe is 0.50 m/s, what is the velocity in a 75-mm-diameter jet issuing from a nozzle attached to the pipe?
Water at a pressure of 294 3 kN/m flows through a horizontal pipe of 100 mm diameter with a velocity of 2 m/s. If the diameter of the pipe gradually reduces to 50 mm, what is the axial force on the pipe assuming no loss of energy.
In an experiment a jet of water of diameter 20 mm is fired vertically upwards at a sprung target thatdeflects the water at an angle of 120° to the horizontal in all directions. If a 500g mass placed on thetarget balances the force of the jet, what is the discharge of the jet in litre/s?
Water flows from a large tank through an orifice of 75 mm diameter and against a block as shown in the figure. The water jet strikes the block at the vena contrata. The block weighs 223 N and the coefficient of friction between the block and the floor is 0.57. The coefficient of discharge C = 0.60 and its coefficient of contraction Cc = 0.62. What is the minimum height to which water must rise in the tank in order to start the block moving to the right?
Include appropriate diagram and sketch. Air flows steadily at low speed through a horizontal nozzle (by definition a device for accelerating a flow), discharging to atmosphere. The area at the nozzle inlet is 0.1m². At the nozzle exit, the area is 0.02m². Determine the gage pressure required at the nozzle inlet to produce an outlet speed of 50 m/s.
A plant has installed a single suction centrifugal pump with a discharge of 68 m3/hr under 60 m head and running at 1200 rpm. It is proposed to install another pump with double suction but of the same type to operate at 36.27 m head and deliver 90 m3/hr. Determine the speed of the new pump. What should be the new impeller diameter if the diameter of the original pump is 140mm?
List at least two common examples of fans, of blowers, and of compressors.
If the velocity of flow in a 75 mm diameter fire hose is 0.5 m/s,what is the velocity in a 25 mm diameter jet issuing from anozzle attached at the end of the pipe.