What does this voltage range pertain to? 6.5 Electrical Characteristics: LM158A, LM358A, LM158, LM258V* = +5.0 V, See(2), unless otherwise statedLM158ALM358ALM158, LM258PARAMETERTEST CONDITIONSUNITMINTYPМАХMINΤYPМАХMINΤYPМАXInput Offset VoltageSee(3), TA = 25°C12232mvIN(+) or lIN(-), TA = 25°C,VCM = 0 V,(4)|Input Bias Current20504510045150nAIN(+) - lIN(-), VcM = 0V, TA =25°C|Input Offset Current210330nA|Input Common-ModeV* = 30 V,(5)%3DVoltage Range(LM2904, V* = 26V), TA =25°CV+-1.5V+-1.5V*-1.5V%3D30of

Input Common-Mode Voltage Potential at Inverting terminal equal to Noninverting terminal A minor…

6.5 Electrical Characteristics: LM158A, LM358A, LM158, LM258 V* = +5.0 V, See(2), unless otherwise stated LM158A LM358A LM158, LM258 PARAMETER TEST CONDITIONS UNIT MIN TYP МАX MIN ΤYP MAX MIN ΤYΡ MAX Input Offset Voltage See(3), TA = 25°C 1 2 2 3 2 5 IN(+) or lIN(-), TA = 25°C, VCM = 0 V,(4) Input Bias Current 50 45 100 45 150 nA IN(+) – lIN(-), VcM = OV, TA = 25°C Input Offset Current 10 30 30 nA Input Common-Mode V* = 30 V,(5) Voltage Range (LM2904, V* = 26V), TẠ = 25°C V*-1.5 V*-1.5 V*-1.5 V 20

6.5 Electrical Characteristics: LM158A, LM358A, LM158, LM258 V* = +5.0 V, See(2), unless otherwise stated LM158A LM358A LM158, LM258 PARAMETER TEST CONDITIONS UNIT MIN TYP МАX MIN ΤYP MAX MIN ΤYΡ MAX Input Offset Voltage See(3), TA = 25°C 1 2 2 3 2 5 IN(+) or lIN(-), TA = 25°C, VCM = 0 V,(4) Input Bias Current 50 45 100 45 150 nA IN(+) – lIN(-), VcM = OV, TA = 25°C Input Offset Current 10 30 30 nA Input Common-Mode V* = 30 V,(5) Voltage Range (LM2904, V* = 26V), TẠ = 25°C V-1.5 V-1.5 V*-1.5 V 20

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter3: Magnetic Starters

Section: Chapter Questions

Problem 30SQ

See similar textbooks

Similar questions

*(a) What is the voltage difference across R6?(b) What are the voltages at nodes 1, 3, and 4 if node 2 isselected as the ground node instead of node 1?
The circuit of the Figure below has Z1= 5 angle 0 , Z2= 9 angle 30 and Z3= 10 angle 80, and is supplied by a 3-phase 450-V solve for IaThe answer must be 110.29 angle -36.52
FIND CURRENT FLOWING THROUGH Z5 FIND CURRENT FLOWING THROUGH Z6
Can someone please explain how to convert V1=-0.4220 to poloar phasor form? (V1=0.578<0)
A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the source voltage and the current through the circuit? a. Insufficient information is given. b. The source voltage will lag the current. c. The source voltage will lead the current. d. The source voltage will be in-phase with the current.
Why there is some solution that is 0.59 A? What would be the final correct answer for this problem?
the root locus (draw asymptotes, find their angles, break away points etc ) for the follo aymmddetermmethevalucofkwhmhmakesthesystmnomllmry What is the fre (Nul:e. If you do not show your complete work, credits will not be assigned) k Gl - N L)
6-10) Using what you have learned constructing the phasor diagram for the LRC series circuit, construct a diagram for the LRC parallel circuit. Derive an expression for the circuit impedance Z and the phase angle φ between the applied emf and the current supplied by the emf. HINT: in the series circuit, the current through all four components was the same. Ask yourself what the components in this arrangement have in common.
the answer is correct but first is how did you know that I2 flows through zB and on that basis you solved the question? second is when i did i2 i got 2+0.266j so can you show how 0.8-.08j was calculated?? what is zs and where did u get 2<90 from? please elaborate on all these points and solve in detail
A. Find the following requirements in plotting the root locus. number of branches number of asymptotes asymptote real-axis intercept asymptote line angles real-axis break-away points / break-in points points at the jw-crossing B. Manually plot the root locus based on the requirements from item A.
give 2 impacts to the end-users per type of single-phase IM in terms of physical features, advantages and applications. Explain each impact not less than 60 words. Type of Single-Phase IM 1. Split-Phase IM 2. Capacitor-Start IM 3. Capacitor-Run IM 4. Capacitor-Start and Capacitor-Run IM 5. Shaded-Pole IM
Solve the following operations. (Final answer must be in polar form.)