69. A load resistor is connected across the open terminals of the circuit shown in Fig. 5.107, and its value was chosen carefully to ensure maximum power trans- fer from the rest of the circuit. (a) What is the value of the resistor? (b) If the power absorbed by the load resistor is three times as large as required, modify the circuit so that it performs as desired, without losing the maximum power transfer condition already enjoyed. 1.2 A Fors 0.8 A FIGURE 5.107 1.8 Ω www 5.4 Ω Ι Σ 3Ω 5Ω 110 COIA 0.1 A

69. A load resistor is connected across the open terminals of the circuit shown in Fig. 5.107, and its value was chosen carefully to ensure maximum power trans- fer from the rest of the circuit. (a) What is the value of the resistor? (b) If the power absorbed by the load resistor is three times as large as required, modify the circuit so that it performs as desired, without losing the maximum power transfer condition already enjoyed. 1.2 A Fors 0.8 A FIGURE 5.107 1.8 Ω www 5.4 Ω Ι Σ 3Ω 5Ω 110 COIA 0.1 A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Know how to design simple voltage-divider and currentdivider circuits 1. Find the value of R that will cause 4 A of current to flow through the80 Ω resistor in the circuit shown.2. How much power will the resistor R from part (a) need to dissipate?3. How much power will the current source generate for the value of Rfrom part (a)?
Calculate the gain of the circuit in the figure below if R1 = 10k ohms, R2 = 100k ohms and RL = 20k ohms. Show complete solution.
For the solar cell attached, find the relative maximum power output for series resistance, Rs of 0 ohms and 5 ohms.
1. Using superposition to get the Thevenin voltage (in volts) seen by the 250Ω resistor, what is the contribution by the 520V source ? 2.If the 250Ω load is change to 100Ω, what is vo (in volts) across the new load?
A 80-W power transistor is to be cooled by attaching it to one of the commercially availableheat sinks. Select a heat sink that will allow the case temperature of the transistor not toexceed (70) °C in the ambient air at 30 °C. uses charts/table also if needed
Use the circuit above to fill out the table below.
1. The terminal voltage and terminal current were measured on thedevice shown. The values of vt and it are provided in the table.Using these values, create the straight-line plot of vt versus it.Compute the equation of the line and use the equation to constructa circuit model for the device using an ideal voltage source and aresistor.2. Use the model constructed in (a) to predict the power that thedevice will deliver to a 25 Ω resistor.
The network of Figure below is the basic biasing arrangement for the field-effect transistor (FET), a device of increasing importance in electronic design. (Biasing simply means the application of de levels to establish a particular set of operating conditions.) Even though you may be unfamiliar with the FET, you can perform the following analysis using only the basic laws introduced in your lectures and the information provided on the diagram. a. Determine the voltages VG and Vs. b. Find the currents 11, 12, Ip, and Is. c. Determine Vps. d. Calculate VDG-
Define three clockwise mesh current from the circuit and employ the supermesh technique to obtain a numerical value for each??
The YCD Company needs to connect 10 mainframe (A-J) computers with cables in a network as shown in the Figure below. The network can take any form, as long as each computer is connected with at least one other computer. All physically possible connections between nodes are shown in the figure below with distances in meters indicated at each cable. Realize the network at minimum cost, which means a minimal total length of cables.
In the circuit shown in the figure, the internal resistance of a voltage source is given as 3 ohms. Load values are such that R = 20 ohms and X = 20 ohms. The effective value of the VAB voltage at the load ends is 220 V. (Frequency is 50 Hz). What is the active power consumed by the load? (Do not take into account 3 ohms in calculations)
Use Kirchhoff’s laws to determine, for the network shown in Figure below, the current flowing in (a) the 20 Ω resistance, and (b) the 4 Ω resistance. Determine also (c) the p.d. across the 8 Ω resistance, and (d) the active power dissipated in the 10 Ω resistance