Answered: A 3-phase, 13.8 kV, 50 MVA alternator…

A 3-phase, 13.8 kV, 50 MVA alternator has positive, negative and zero sequence of 0.20, 0.20 and 0.05 pu. If the alternator is on no-load, determine the fault current for a three-phase fault.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.17P

See similar textbooks

Related questions

Q: For the circuit in Figure 1, switch 1 has been closed for a long time and switch 2 has been open for…

A: The given circuit isWe need to determinea. i(t) at t = 0-.b. i(t) for 0≤t≤1s.c. i(t) for t≥1s.

Q: 1. Draw the timing diagram showing how a toggle flip-flop can be used for a binary counter of a…

A: Given:Frequency divider circuit using T flip-flops with timing diagrams. we need to show: the given…

Q: A parallel resonant circuit has R = 100 kn, L= 20 mH, and C = 5 nF. Calculate wo, w1, 2, Q, and B.

A: A parallel resonant circuit,

Q: From the data, 100 (1 + 0.1 jw) 1-0.0004² + jo.028 TF (W) = 100 (1 + jw) 10 TF(W) = Factor It jw TF…

Q: please could give a simplified drawn schematic/diagram to show a how microcontroller is connected…

A: The above question is based on the interfacing of a microcontroller to a relay circuit.

Q: 11. A circuit for a gated D latch is shown below. Assume that the propagation delay through either a…

A: Given:a D latch circuit, The propagation delay for the inverter and AND gate is 1 ns. we need to…

Q: A circular ring of charge of radius a lies in the x-y plane and is centered at the origin. Assume…

A: The radius of circular ring, The charge density,

Q: Question #6 Given the following parallel circuit Hill+ R₁ 20 Ω 11 12 R2 30 Ω If the voltage of the…

Q: A manufacturing plant has a load of 3650 Kva at a lagging power factor of 0.6635. A 500 hp…

A: Load apparent power(s)=3650 kVAExisting Power factor(PF)= 0.6635Desired power factor(PF)=…

Q: Question 11: Let x(t) = u(t-2)-u(t-4) +5(1-6) and h(t)= eu(t). Compute y(t)= x(t) *h(t).

Q: Infinitely many long, straight conductors with square cross sections are laid side-by-side to form…

Q: A telephone line has the following parameters R = 40Nm^(-1), G = 400\mu Sm^(-1), L = 0.2\mu Hm^(-1),…

Q: For the circuit below, find i(t) fort t > 0 assuming that the switch opens at t = 0 after being…

A: In this question, we need to determine the current i(t) as shown in the circuit. We know, inductor…

Q: a) Complete the following Table Q.1a. All numbers are 8 bits. + Decimal -103 Table Q.1a Signed…

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Q: 7. Packaging will be done in a factory with an automation system: -In the first stage the product…

A: According to the question, we need to write an FBD program for the given condition.Packaging will be…

Q: ST= ST= |ST|= P₁ = QT= For Blank 7 2 untis units units units Calculate the total current and power…

Q: Calculate the maximum horsepower of an induction motor at 0.8 power factor and 85.5 percent…

Q: Problem 1: Question A DC resistive circuit includes a 5.5 mA current source, Is, which is connected…

Q: 14. For the RLC circuit shown L₁ 103mH, R₁ = 13602, C₁= 16.7μF, Em = 6.78V, = L₂= 203mH, R₂ = 10002,…

A: Given Data:An RLC circuit with,Input peak voltage Supply frequency To Find:The expression of .The…

Q: Describe Lithography and Gate Oxide formation procedures in fabrication process.

A: In the given question, we need to describe the Lithography and Gate Oxide formation procedures in…

Q: 6. The gated SR latch in Figure 5.5a (from Text (Brown), reproduced below) has unpredictable…

A: The gated SR-latch given byThe characteristic table of gated SR-latch isThe timing diagram is given…

Q: Write the expression for v. (t) for t≥ 0+. Express your answer in terms of t measured in seconds so…

A: The expression for voltage across the inductor for t>0 needs to be calculated. The expression can…

Q: A 12-cm long elastic resistive sensor with a 6-mm diameter has a resistance of 1.2 ΚΩ. (a) Calculate…

A: Length (L)= 12cm=0.12mDiameter (d)= 6mm= 0.006mResistance (R)=1.2k=1200Circumference (C)=1.2mthere…

Q: a)Determine a numerical value for each current and voltage (i1, v1, etc.) in the circuit shown…

A: For the given circuit the value of the voltage and the current in the circuit needs to be calculated…

Q: Find Vc

A: For the given circuit the value of the voltage across the capacitor needs to be calculated and the…

Q: (c) Your friend Lynn Year looks at this circuit and says this can be modeled as a voltage controlled…

A: According to the question, for the given circuit as shown belowWe need to find the value of…

Q: A 100 kVA, 2500/125V, 50Hz, step down transformer has the following parameters: RH = 1.5 Ω, Χμ = 2.8…

A: Given information,Rated output kVA.Induced EMF ratio Volts.So turns ratio is .Supply frequency…

Q: . In the given circuit, both switches have been in their previous positions for a long time. At t =…

Q: Use nodal analysis to find current i, in the circuit. Let i, 6 cos(200t + 15°) A. 0.1 vo is 20 2 Vo…

Q: Question 3 Find the Norton equivalent circuit at terminals a-b in the circuit in the fig. 90/30° V…

A: Given:a circuit,we need to compute norton's equivalent.

Q: Find the Thévenin equivalent circuit external to R, in the circuit, then determine the current…

A: In the given questions we need to calculate the thevenin equivalent circuit and R5.

Q: 2. Consider the following circuit. The circuit parameters are VDD = 3.3V, RD = 8kQ2, R₁ = 240kQ2, R₂…

Q: K-MAP THE FOLLOWING. SIMPLIFY THE LOGIC EQUATION FOR Z, IF POSSIBLE. THEN SIMPLIFY THE LOGIC…

A: Given Data:A truth table with,Inputs output To Find:The simplified logic expression for .The…

Q: A 3Φ electrical machine wye connected has an output of 20 horse power and a lagging power factor of…

A: Let the supply voltage is 400 V.Output power is given as, Lagging power factor Efficienncy

Q: Vsig Rsig Rin RB1 RB2 If Vsig = 20 mV value of Vout. ww Vcc www peak' Rc Rout RE RL = The…

A: We need to find out peak value of output voltage for the given circuit.

Q: Find the transfer functions for the following block diagrams:

A: For the given block diagram the transfer function of the system needs to be obtained and the same…

Q: What are the expected readings of the following in the figure below? (R = 5.80 02, AV = 5.50 V) (A…

Q: - V = ? 3√2 зл ми ми min 322 1.32 1.5√2 ← Samp/s oc on Determine the supply voltage in the following…

A: The circuit diagram,

Q: Draw Stick Diagram of Boolean Function 1- Y=D.(C+B.A)

A: According to the question, we need to draw the stick diagram of the following function

Q: a. Determine the characteristic equation(s). b. Determine the system natural frequency or…

Q: л-pad attenuators are commonly used in radio frequency and microwave transmission lines and can be…

A: The given circuit isWe need to determine the current through R3 and R5 using super position…

Q: c. The output voltage is measured between points 2 (+) and 0 (-). Find the ratio of the input to the…

Q: Problem 5 Find i(t) for t> 0 for the circuit below. 4Ω 12 V (+ t = 0 5 H ↓i(t) -18 F 5Ω 13 A

A: The given circuit is We need to determine the expression of the current i(t) for t > 0.

Q: Answer: For the following state table, complete the timing trace for the state q as far as you can.…

Q: using 1 uF capacitors and ideal op amps, design a high-pass Butterworth filter with a cutoff…

A: cutoff frequency of 8kHzstopband frequency 500 Hzgain=-85dB at 500Hzcapacitance= 1=

Q: 4. Analyze the following digital circuit that contains a T flip-flop with initial condition Q = 0.…

A: For the given sequential circuit the timing waveform of the input T and the output of the flip flop…

Q: Question #7: For the original bandlimited signal shown below, schematically draw the output…

Q: 1. For each of the circuits shown in Figure, a) find the equivalent resistance seen by the source,…

Q: Design a combinational circuit that compares two 2-bits numbers using a truth table according to: 1)…

Q: If A=2xz², what is the curl of this vector, V XA, in Cartesian coordinates? B 222 xz² -îz² -ŷz²

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

Please help with this question do not use chat gpt please

A 3-phase, 13.8 kV, 50 MVA alternator has positive, negative and zero sequence of 0.20, 0.20 and 0.05 pu. If the alternator is on no-load, determine the fault current for a three-phase fault.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Understanding the Problem and Calculating the Base Impedance

VIEW

Step 3: Calculating the Fault Impedance and Converting the Fault Impedance to Ohms

VIEW

Step 4: Calculating the Fault Current

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

a) In Three Phase Faults that will occur separately on A, B, C and D Busbars, Calculate the currents. b) Maximum fault currents to pass through KA, KB, KC1, KC and KD Protection devices determine. Help me please... Thank you so much.
A 3-phase, 13.8 kV, 10 MVA alternator has positive,negative and zero sequence reactances of 0.20, 0.020 and0.10 pu. Determine the fault current if a double line toground fault occurs.
Two alternators rated 30 MVA and 20 MVA have per unit reactance of 0.30 and 0.50 respectively are connected to a common 12-kV bus bar. Solve the fault current if a symmetrical 3-phase fault occurs at the bus bar.
A GENERATOR IS RATED 500 MVA 22KV THE POSITEVE ,NEGATIVE AND ZERO SEQUENCE COMPONENTS OF THE GENERATOR ARE 0.20 ,0.20 AND 0.05 PER UNIT RESPECTIVELY .WHAT IS THE RATIO OF THE FAULT CURRENT FOR A SINGLE LINE TO GROUND FAULT TO THE FAULT CURRENT FOR A THREE-PHASE FAULT?
A 10 MVA, 6.9 kV alternator has a positive, negative andzero sequence per unit reactance components of 0.30, 0.25 and 0.05 respectively. If the neutral of the generator isgrounded through a reactor of 0.48 ohms, determine the fault current during a single line to ground fault.
In a 3 phase, 3 wire system, it has normal voltage of 10.4kV line to line fault occurs at generator terminal, what is the value of the fault current? When positive and negative sequence impedance is 0.6Ohm and 0.5Ohm respectively
answer both i will rate.... a. In sequence networks of power system, why does voltage sources appear only in the positive sequence? b. Describe the main differences in fault protection objectives when dealing with a temporary fault vs a permanent fault.
For the following network, calculate the fault currents (IF1, IF2, IF3 and IF4) in pu and in kA, and circuit breaker ratings (i.e. fault MVA ) at the indicated locations. Internal reactance of generators are j0.9 pu. Base quantities: 11 kV, 400 MVA on the generator side.
A 30kV, 50MVA generator having a solidly grounded neutral and Z1 = 0.25pu, Z2=0.15pu and Z0=0.05pu. a. Calculate the fault current and voltages for a single line to ground fault. b. Sketch the phasor diagram for the fault voltages.
A generator is rated 100 MVA, 15 kV. It is Y-connected, solid grounded and is operated at rated voltage at no-load and is disconnected from the rest of the system. Its positive and negative sequence reactances are 0.10 p.. and its zero sequence reactance is 0.05 p.. Calculate in ohms of inductive reactance to be inserted in the neutral connection of the generator to limit the fault current for a single line to ground fault to the fault current of a symmetrical three-phase fault.
A 3-phase, 22 kV, 100 MVA alternator has positive, negative and zero sequence reactances of 0.3 p.u, 0.3 p.u. and 0.05 p.u., respectively. What is the negative sequence component for a line to line fault?
Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and the motors are as shown in the figure. The reactance of lines 1 and 2 are 40 ohms and 50 ohms respectively. Assume that system is unloaded, and the generators are generating their rated voltage. Select the generator G₁ ratings as base values. Choose the fault location in bus 3. And give the bellow answer For a symmetrical three phase fault on the bus 3 1. Calculate the fault current in ampere and fault power in MVA and the fault current contribution from the generator connected to the bus 3.