69. Which of the following instrument is used for angular measurement? Select one: a.COMPARATOR b.MICROMETER c.SINE BAR d.OPTICAL FLAT

Q: Q.6) Complete the following table: No. Part of vernier calliper 1 Main Scale Vernier Scale 3 Screw

A: The main scale reading is that to the left of the zero on the vernier scale. The vernier reading…

Q: The advantage of Vernier caliper over Micrometer is Select one: O a. Both devices not useful O b.…

A: Option d is correct.

Q: Steps in the procedure of measuring the volume of liquid using a graduated cylinder.

A:

Q: 6. What is accuracy in measurement?

A: Measurement:  It is the numerical quantification of the attributes for a body that are used to…

Q: In transition fit, tolerance zone of hole is entirely above that of shaft tolerance zones of hole…

A:

Q: Displacement Volume - Retraction 11 Calculate the volume of the cylinder during retraction.…

A:

Q: - The dimensions for the shaft size are o10*00 0.009 mm and the hole size are b 10*0.015 +0.000 mm.…

A: Shaft sizeϕ10-.009+0.00Maximum limit of shaft =10+0.000=10.00 mmMinimum limit of shaft=…

Q: 6. What material is used 7. What is the unspecified tolerance for angular dimensions? 8. What is the…

A: Given figure  CHART DOWEL SPLIT TYPE  TO FIND :  7 .What is the unspecified tolerance for angular…

Q: per use to block mo

A: introduction: In the steel business, the vernier calliper is a crucial tool. It's a tool for…

Q: Differentiate between operation               (i) Plain Turning and Facing operation…

A: Plain turning and Facial operation: plain turning is the operation of removing extra amount of…

Q: Try square is a measuring tool used to measure the straightness and squareness of a workpiece.…

A: The square of the measure consists of two main elements, the blade, often referred to as a beam or…

Q: The depth measurement is done by ___________________part of a Vernier Caliper. Ratchet Anvil Spindle…

A:

Q: Describe two scales in Vernier Caliper?

A: Vernier caliper instrument is mainly used for taking accurate linear measurements. Vernier caliper…

Q: among the ruler and vernier caliper gave the least % err

A: Ruler and vernier caliper both are measuring devices.

Q: ribe a situation where you might use a Vernier caliper or micrometer. Explain why you would use this…

A: We need to discuss where we can use vernier caliper/ micrometer

Q: What is center of percussion? Write down Procedure for finding COP of a wooden compound pendulum

A: Given;To define contre of percussionTo write procudure for finding COP  of a wooden compound…

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: 1st image : What is the reading on the micrometer? 2nd image : What is the reading on the…

A:

Q: How can angular displacement be determined by angular acceleration?

A:

Q: If the basic diameter of shaft is 20mm with -0.02mm unilateral tolerance, and diameter of hole is…

A:

Q: What is an advantage of advantage of the metric system over the u.s. customary system?

A: The metric system is a worldwide standardly used unit system for measurements and it is used in…

Q: 9) To obtain a guide for centering irregular shaped workpiece in the lathe, its face should be laid…

A:

Q: ___________ tool is used for verifying the flatness of the component.     A. Protractor…

A: Protractor is a device used to measure the angles. Engineers square is a checking tool which is used…

Q: What component does a tubular inside micrometer include that allows it to measure a wide range of…

A: Adjustable anvil is the correct answer.

Q: The tool used for marking center is __________. a.   Steel rule   b.   Divider   c.…

A: Solution:

Q: What is the use of gyroscope compass?

A: Gyroscope compass is a nonmagnetic device based on spinning disc and rotation of earth.

Q: The advantage of Vernier caliper over Micrometer is Select one: a. Both devices not useful b. Not…

A: vernier calipers is used to measure inner, outer dimensions and depth can also be measured.

Q: er than 5mm annot be used when position ta han 0.1mm annot be used when position ta er than 4mm

A: Given Data : Counter sink fasteners

Q: Which of the following is not a type of direct measuring instrument? a Micrometre Ob Vernier…

A: Among the given instrument names, it is required to state the name of the instrument that is not a…

Q: Refer to the Ø.750 dimension. A) Where is the tolerance specified ?…

A: 1—position 2 – the shape of the tolerance zone

Q: Which of the following will brake of blades O a.

A: Angle Of Blades

Q: Explain anyone practical measurement system with all of its functional elements.

A:

Q: List three rules to follow when using or storing semi-precision measuring tools.

A: Semi precision tools are used for the measurement of the various dimensions of the workpiece.

Q: what is the most digital multimeters can measure?

A: A digital multimeter is a measuring instrument used to measure two or more electrical values mainly,…

Q: State any THREE conventions in dimensioning.

A:

Q: Countersinking process is carried out by using twist Drilll. O True O False

A:

Q: 18. Which is not an equation for determining RPM: A. surface speed x 12/ pix diameter (in.) B.…

A:

Q: Surface grinding is done to produce

A: grinding is a machining operation in which extra material on the workpiece is removed. in grinding,…

Q: Right the accuracy in millimete

A: The screw gauge with a micrometer. The micrometer screw gauge is used to measure dimensions that are…

Q: With what precision caliper type can we measure 19,86 mm measurement? O A) 1/10 mm O B) 1/50 mm C)…

A: We can measure the value if the least count is come to the smallest measuring range...

Q: From the value in table 1.1 calculate the precision of Oth measurement?

A: Precision refers to the consistency of an instrument. It can be calculated as following: Precision =…

Q: wheel

A: Correct answer is given below

Q: A steel cylinder 5 inch in diameter is to be machined in a lathe. If the desired linear velocity of…

A: Given information V=2.3 ft/sec=2.3*12 in/sec, D=5in

Q: Which of the following is the correct sequence of the ability of the machining process to produce…

A: There are many processes which are used to get better surface finish. The type of machining process…

Q: Identify the  part not belonging to micrometer. Frame Ratchet Locknut Clamp

A: Identify the  part not belonging to micrometer. Frame Ratchet Locknut Clamp