6a. Water goes through an inlet pipe at 5.0 × 10° Pa with a speed of 6.0 m/s. If the inlet pipe has a diameter of 4.o cm and goes down by 10.0 m to an outlet pipe with a diameter of 2.0 cm, find the water pressure, speed, and volume flow rate at the outlet pipe. How long does would it take to fill spherical water tank at the outlet pipe if the tank has a diameter of 12.0 m? Illustrate the inlet pipe, outlet pipe, and the tank (need not be drawn to scale). Label their corresponding flow speeds and pressures. Define your coordinate system.

6a. Water goes through an inlet pipe at 5.0 × 10° Pa with a speed of 6.0 m/s. If the inlet pipe has a diameter of 4.o cm and goes down by 10.0 m to an outlet pipe with a diameter of 2.0 cm, find the water pressure, speed, and volume flow rate at the outlet pipe. How long does would it take to fill spherical water tank at the outlet pipe if the tank has a diameter of 12.0 m? Illustrate the inlet pipe, outlet pipe, and the tank (need not be drawn to scale). Label their corresponding flow speeds and pressures. Define your coordinate system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water from a reservoir passes over a dam through a turbine and discharges from a 70-cm ID pipe at a point 95 m below the reservoir surface. The turbine delivers 0.950 MW. Calculate the required flow of water in m3/min if friction is neglected. If friction were included would a higher or lower flow rate be required? (Note: The equation you will solve in this problem has multiple roots. Find a solution less than 1.0 m3/s.) V=___m^3/min?
The pressure drop across a turbine is 200kPa. The flow rate is 0.25m3/min. WHat is most nearly the power output of the turbine?
The waterwheel in Fig. is being driven at 200 r/minby a 150-ft/s jet of water at 20 ° C. The jet diameter is 2.5 in.Assuming no losses, what is the horsepower developed bythe wheel? For what speed Ω r/min will the horsepowerdeveloped be a maximum? Assume that there are manybuckets on the waterwheel.
Q9: Find the specific speed and power consumption for pump having the following properties: (Q=0.1 m3/s), (speed=725 r.p.m) and (head =15 m).
A pump delivering 0.23 m3/s of water has a 304.8mm diameter suction flange and 254mm discharge flange. The suction pipe is 3.66m long and the discharge pipe is 22.86m long. Neglecting the turbulence losses in the pipe, find: a.) the head which the pump must deliver ( in meters ) b.) the motor power in KW required if the efficiency is 80%, c.) the reynold’s number and type of flow in the suction pipe d.) the reynold’s number and type of flow in the discharge pipe
A centrifugal pump developing 9 ft head at 1200 rpm is driven by a 3 hp motor. Impeller diameter is 6-in. Discharge is 1300 gpm. Determine the critical cavitation parameter ?
1. A Pelton wheel of 4 m diameter operates with a head of 1000 m. Estimate the flow rate and power output of the machine, assuming that it operates at peak efficiency and there are no losses in the flow upstream of the turbine. 2. A Pelton wheel operates with a head of 400 m at 350 rpm, and it is powered by a jet 12 cm in diameter. Find the specific speed (U.S. customary units), and the wheel diameter, if there are no losses in the flow upstream of the turbine and it operates at peak efficiency.
A pipe 50 cm in diameter carries water (l0°C} at a rate of 0.5 m 3 / s. A pump in the pipe isused to move the water from an elevation of 30 m to 40 m. The pressure at section 1 is 70kPa gauge, and the pressure at section 2 is 350 kPa gauge. What power in kilowatts and inhorsepower must be supplied to the flow by the pump? Assume h L = 3 m of water and α 1 =α 2 = 1. Find the following Draw the Schematic diagram Drive the energy equation Calculate pump head Power requirement
The pressure of the water base of a Pelton Wheel is 4850 kPa and the velocity at the same point is 6 m/s. The jet diameter is 20 cm, and the velocity coefficient is 0.98 and the turbine’s efficiency is 86%. Find the brake power, in bkw.
Water flows through the reducer, the inlet diameter is 20 cm and the outlet diameter is 10 cm. If the velocity at the inlet is 0.4 m/s and the pressure 107, what is the pressure in kPa at the exit? Assume frictionless flow with no heat loss.
A 5 MW turbine is developed under an effective head of 320 m. The turbine efficiency is85%. Velocity coefficient of the nozzle is 99%.(a)Select which is the appropriate turbine based on effective head. (b)What should be the wheel diameter in meters assuming it is 12 times the diameter of the jet?
A fi reboat pump delivers water to a vertical nozzle with a3:1 diameter ratio, as in Fig. . If friction is neglectedand the fl ow rate is 500 gal/min, how high will the outletwater jet rise?( a ) 2.0 m, ( b ) 9.8 m, ( c ) 32 m, ( d ) 64 m, ( e ) 98 m