7: horizontal steel pipe having a diameter of 5 cm is maintained at a temperature of 50◦C in a large room where the air and wall temperature are at 20◦C. The surface emissivity of the steel may be taken as 0.8. Using the data of Table 1-3, calculate the total heat lost by the pipe per unit length. Example 7: horizontal steel pipe having a diameter of 5 cm is maintained at a temperature of 50•Cin a large room where the air and wall temperature are at 20•C. The surface emissivity of the steelmay be taken as 0.8. Using the data of Table 1-3, calculate the total heat lost by the pipe per unitlength.

7: horizontal steel pipe having a diameter of 5 cm is maintained at a temperature of 50◦C in a large room where the air and wall temperature are at 20◦C. The surface emissivity of the steel may be taken as 0.8. Using the data of Table 1-3, calculate the total heat lost by the pipe per unit length.

7: horizontal steel pipe having a diameter of 5 cm is maintained at a temperature of 50◦C in a large room where the air and wall temperature are at 20◦C. The surface emissivity of the steel may be taken as 0.8. Using the data of Table 1-3, calculate the total heat lost by the pipe per unit length.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.51P

See similar textbooks

Similar questions

1.15 A thermocouple (0.8-mm-diameter wire) used to measure the temperature of the quiescent gas in a furnace gives a reading of . It is known, however, that the rate of radiant heat flow per meter length from the hotter furnace walls to the thermocouple wire is 1.1 W/m and the convection heat transfer coefficient between the wire and the gas is K. With this information, estimate the true gas temperature. State your assumptions and indicate the equations used.
1.13 If the outer air temperature in Problem is –2°C, calculate the convection heat transfer coefficient between the outer surface of the window and the air, assuming radiation is negligible.
Determine the power requirement of a soldering iron in which the tip is maintained at 400C. The tip is a cylinder 3 mm in diameter and 10 mm long. The surrounding air temperature is 20C, and the average convection heat transfer coefficient over the tip is 20W/m2K. The tip is highly polished initially, giving it a very low emittance.
1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
1. A composite furnace wall is made up of a 12-in. lining of magnesite refractory brick, a 5-in.thickness of 85% magnesia, and a steel casing 0.10-in. thick. Flue gas temperature is 2200 F andthe boiler room is at 80 F. Gas side film coefficient is 15 Btu/hr-sq.ft-F and air side is 4.0.Determine:a. The thermal current Q/Ab. Interface temperaturesc. Effect on thermal current and inside refractory wall temperature if the magnesia insulation weredoubled.
Write the expression for critical radius of insulation for a cylindrical pipe. Consider aninsulated pipe exposed to the atmosphere. Will the critical radius of insulation begreater on calm days or on windy days? Why?
A furnace wall is to consist in series of 7 in of kaolin firebrick, 6 in of kaolin insulating brick, and sufficientfireclay brick to reduce the heat loss to 100 Btu/ hr ft2 when the face temperatures are 1500 and 100°F,respectively.a) Show the figure of the systemb) What thickness of fireclay brick should be used?c) If an effective air gap of 1/8 in can be incorporated between the fireclay and insulating brick whenerecting the wall without impairing its structural support, what thickness of insulating brick will berequired?