P3.137 In Fig. P3.137 the fluid is gasoline at 20°C at a weightflux of 120 N/s. Assuming no losses, estimate the gagelen.a,pressure at section 1.Inn5 cmОрenjetP112 mBeni2ite inthe10 поthe8 cmPaР3.137

Name: P3.137 In Fig. P3.137 the fluid is gasoline at 20°C at a weightflux o
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: P3.137 In Fig. P3.137 the fluid is gasoline at 20°C at a weightflux of 120 N/s. Assuming no losses, estimate the gagelen.a,pressure at section 1.Inn5 cmОрenjetP112 mBeni2ite inthe10 поthe8 cmPaР3.137

Calculate the discharge as follows:

Answered: 7 In Fig. P3.137 the fluid is gasoline…

Engineering

Mechanical Engineering

7 In Fig. P3.137 the fluid is gasoline at 20°C at a wcight flux of 120 N/s. Assuming no losses, estimate the gage pressure at section 1. 5 сm Оpen jet 12 m 2 8 cm Р3.137

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If losses are neglected in Fig. P3.133, for what water levelh will the flow begin to form vapor cavities at the throat ofthe nozzle?
Water fl ows through a circular nozzle, exits into the air as a jet,and strikes a plate, as shown in Fig. P3.114. The force requiredto hold the plate steady is 70 N. Assuming steady, frictionless,one-dimensional fl ow, estimate ( a ) the velocities at sections(1) and (2) and ( b ) the mercury manometer reading h .
A tank contains 1 m3 of water at 20°C and has a drawn capillaryoutlet tube at the bottom, as in Fig. P6.63. Findthe outlet volume flux Q in m3/h at this instant.
In Fig. water exits from a nozzle into atmosphericpressure of 101 kPa. If the fl ow rate is 160 gal/min and frictionis neglected, what is the gage pressure at section 1?( a ) 1.4 kPa, ( b ) 32 kPa, ( c ) 43 kPa, ( d ) 29 kPa, ( e ) 123 kPa
Water at 20 ° C fl ows steadily through the tank in Fig.P3.101. Known conditions are D 1 = 8 cm, V 1 = 6 m/s, andD 2 = 4 cm. A rightward force F = 70 N is required to keepthe tank fi xed. ( a ) What is the velocity leaving section 2?( b ) If the tank cross section is 1.2 m 2 , how fast is the watersurface h ( t ) rising or falling?
A 20 °C water jet strikes a vane mounted on a tank withfrictionless wheels, as in Fig. P3.61. The jet turns and fallsinto the tank without spilling out. If θ =30 ° , evaluate thehorizontal force F required to hold the tank stationary.
The long pipe in Fig. P3.172 is fi lled with water at 20 ° C.When valve A is closed, p 1 - p 2 = 75 kPa. When the valveis open and water fl ows at 500 m 3 /h, p 1 - p 2 = 160 kPa.What is the friction head loss between 1 and 2, in m, for thefl owing condition?
Consider Fig. P3.36 as a general problem for analysis of amixing ejector pump. If all conditions ( p , ρ , V ) are knownat sections 1 and 2 and if the wall friction is negligible,derive formulas for estimating ( a ) V 3 and ( b ) p 3 .
Water fl ows steadily through the box in Fig. P3.63. Averagevelocity at all ports is 7 m/s. The vertical momentum forceon the box is 36 N. What is the inlet mass fl ow?
A fi reboat draws seawater (SG = 1.025) from a submergedpipe and discharges it through a nozzle, as in Fig. P3.176.The total head loss is 6.5 ft. If the pump efficiency is75 percent, what horsepower motor is required to drive it?
In a horizontal pipe water flows at a rate of 9.1 L/s. Here, the pipe has two sections, one with a diameter of 10.16 cm and the other with a diameter of 5.08 cm, with a gradual smooth reducing section. In this case, a mercury manometer is used to measure the pressure difference. If friction is negligible how would I find the differential height of mercury between the two sections? If the manometer on the 5.08cm pipe section was replaced with a pitot tube how would the reading change? any help would be deeply appreciated
In Fig. P3.121 the fl owing fl uid is CO 2 at 20 ° C. Neglect losses.If p 1 = 170 kPa and the manometer fl uid is Meriam red oil(SG = 0.827), estimate ( a ) p 2 and ( b ) the gas fl ow rate in m 3 /h.