7. A single stage amplifier has a 200 kHz bandwidth and a voltage gain of 100 at 290 K temperature. ASsume that the external noise is negligible and that 1mV signal is applied to the amplifier's input. Calculate the output noise voltage if the amplifier has a 5-dB NF and the input noise is generated by a 2 kiloohm resister.

7. A single stage amplifier has a 200 kHz bandwidth and a voltage gain of 100 at 290 K temperature. ASsume that the external noise is negligible and that 1mV signal is applied to the amplifier's input. Calculate the output noise voltage if the amplifier has a 5-dB NF and the input noise is generated by a 2 kiloohm resister.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The noise produced by a resistor is to be amplified by a noiseless amplifier having a voltage gain of 75 and a bandwidth of 100 kHz. A meter connected to the output of the amplifier reads 240 μV RMS. Assuming operation at 37°C, calculate the resistor’s resistance. In the previous problem, if the bandwidth were cut to 25 kHz, determine the expected output meter reading. A. 240 μV B. 60 μV C. 120 μV D. 75 μV
1.A voltage amplifier is used to amplify radio signals from the antenna in a car radio system. The incoming radio signal voltage from the antenna, vs = 500 mV and its resistance is Rs = 100 N. Assume the open circuit voltage gain of the amplifier, 100 and the output resistance is 1 k. i. Design the amplifier by finding its input resistance, R; if the amplifier voltage gain (vo/vs) is given as 20. ii. If the amplifier output is connected to a speaker (load), find the new amplifier voltage gain (vo/vs) if the load resistance, R1, value is 1 kN.
Class B Amplifier q1)If the input is 7.5Vp-p...DATA COLLECTION: What is the IL(peak)? a)7mA 6)mA 5)mA 4)mA q2) DATA COLLECTION: What is the Idc? a)3.84 b)4.82 c)3.82mA d)1.82mA q3)DATA COLLECTION: What is the input power in DC? Power input = 48.45mW Power input = 45.48mW Power input = 44.58mW Power input = 45.84mW q4) DATA COLLECTION: What is the output power in AC? a)18mW b)81mW c)11.8mW d)18.9mW q5)DATA COLLECTION: What is the power dissapated by each transistor? a)35.1mW b)53.1mW c)15.3mW d)13.5mW q6)DATA COLLECTION: What is the efficiency of class B amplifier? a)45% b)40% c)63% d)33% q7)
The input resistance of the amplifier used in the oscillator circuit shown in the picture is very large. No-load voltage gain is given as K0 = 5. For L = 0.1mH; Calculate the value of C1 and C2 capacitors for the circuit to oscillate at f0 = 2MHZ.
7. When the automatic gain control voltage of a radio receiver is measured with a vacuum tube voltmeter whose input resistance is 10 M-ohm, it reads 4.5 V. When an ordinary voltmeter whose input resistance is 10 k-ohm is also connected across the AGC voltage source, both meters read 0.40. What is the internal resistance of the AGC voltage source? 8. A phonograph pick up develops an open-circuit emf of 50 mV and has an internal resistance of 1200 ohm. A. What voltage will it develop across a 4 ohms load resistance? B. What value of load resistance must be used to obtain a 75% eff? C. What is the maximum power output of the pickup? 9. What bleeder resistor is required to complete a voltage divider to give 300 v at 40 mA from a 500 V source of emf if the series dropping resistor is 4 k-ohm.
The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20kHz. A meter connected to the output of the amplifier reads 1mV rms. (a) The bandwidth of the amplifier is reduced to 5kHz, its gain remaining constant. What does the meter read now? (b) If the resistor is operated at 80°C, what is its resistance?
The partial gain for Vg is -2 ±10% R2 = 1kΩ. R1 = 10kΩ Rf = 2kΩ. Record the amplitude of the signal source (vg), the ac component of the output (vout), and the dc component of the output (VOUT) in Table 3. Test to see whether you have met your design criteria. The measurements that you made in Table 3 should assist you in this. Show the results of your comparisons in Table 4.
A differential amplifier is connected to a supply of Vs = ±10V, and has a nominal gain of 4x105. What is the maximum amplitude of the input differential voltage for the amplifier to work in linear region, i.e. for the output to remain undistorted? Write your answer in standard scientific notation in "e" format. General formulation of the standard scientific notation is: a × 10b , where 1 ≤ a < 10. E format shows that as "aeb". For example, for 2.3 * 105 write 2.3 e5 , or for 1.7*10-3 write 1.7e-3.
A common emitter amplifier as shown in Figure Q2 has the following parameters, β = 100, R1= 33K, R2 = 10K, RC = 3K3, RE = 1K, ro =  and VBE = 0.7 V.State all assumptions made.i. Check whether βRE>>10R2 is satisfiedii. Use the appropriate approach of analysis to determine the Quiescent point; IBQ,ICQ and VCEQ.iii. Draw the small signal equivalent circuit. Determine input impedance, Zin, outputimpedance, Zout, and the voltage gain, AV, if RL=20kΩ.
(a) Define bandwidth of an amplifier and provide explanation using a diagram. (b) A circuit has no lower cut-off frequency but has an upper cut-off frequency of 100 MHz. What is its bandwidth?
A three stage amplifier has the following gains and noise factor for each stage: 1st stage Gain=10 dB and Noise Factor = 2; 2nd stage Gain=16 dB and Noise Factor = 4; and 3rd stage Gain=20 dB and Noise Factor = 5. Suppose another amplifier stage (4th stage) is connected, what would be its noise figure (4th stage) in dB to provide as overall noise factor of 2.3? (Use two decimal places)
For an inverting amplifier if the current I = 1 mA with an internal output resistance of 500 Ω and a V1 = 5 mV calculate the output voltage if the dc voltage gain 60 db?