7. A wooden storage vat is 6 m in diameter and is filled with 7 m of oil, s = 0.8. the wood staves are bound by flat steel bands, 50 mm wide by 6 mm thick, whose allowable tensile stress is 110 MPa. What is the required spacing of the bands near bottom of the vat, neglecting any initial stress?

7. A wooden storage vat is 6 m in diameter and is filled with 7 m of oil, s = 0.8. the wood staves are bound by flat steel bands, 50 mm wide by 6 mm thick, whose allowable tensile stress is 110 MPa. What is the required spacing of the bands near bottom of the vat, neglecting any initial stress?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.3P: A large spherical tank (see figure) contains gas at a pressure of 420 psi. The tank is 45 ft in...

See similar textbooks

Related questions

Q: b) A 3-m-high, 5-m-wide rectangular gate in Figure 2 is hinged at the top edge at A and is…

Q: 7. A pan made of stainless steel contains water at atmospheric pressure. The pan diameter is 25 cm…

A: Given Data The diameter of pan is:d=25 cm=0.25 m The surface temperature is:Ts=116°C The saturated…

Q: A material is subjected to a pressure of 5 MPa. If the material has an elastic modulus of 80 GPa and…

Q: a) An inline crank-slider linkage mechanism is given in Table Q4. Table Q4a Length (mm) Link AB , R…

A: given; radius of crank AB (r)=50mmlength of connecting rod(l)=80mmcurrent position…

Q: 2. With the blocks initially at rest, the force P is increased slowly from zero to 60 lb. Plot the…

A: Acceleration Speed increase, rate at which speed changes with time, regarding both speed and…

Q: Consider the following spring system. C2 with spring constants c= m2 225

Q: Determine the thickness (mm) of a spur gear tooth with a diametral pitch of 7.01, measured along the…

A: Given:- Diametral pitch = 7.01 mm To Find:- Thickness of spur gear tooth

Q: Determine the height of the fluid inside a manometer that is attached to a CO2-filled tank. The…

A: Pressure is defined as the force per unit area. there are two types of pressure absolute pressure…

Q: how that if two bodies of thermal Capacitics C, and Ca at tem atures Ty and Tz are means of a…

Q: A tank contains mercury up to a height of 0.3 m over which water stands to a depth of 1 m and oil of…

Q: If the viscosity of water at 68 °C is 0.00418 poise and its specific gravity is 0.981 determine the…

Q: Determine the type of flow does the water has if it flow in a .5m diameter pipe with a velocity of…

A: Determine the type of flow .

Q: what must the area of the connected large piston be to exert a force of 6550 N?

A: To find Area of large piston.(A2)

Q: I need to write about theory of vibration with application, using the ruler (about one page)…

A: A vibration is a fluctuating motion around a fixed point. Vibration may be classified into two…

Q: Q1 The vibration of a car is modelled as a damped single degree-of-freedom system with the following…

Q: Figure 1: Undamped single degree-of-freedom system a) Show the natural frequency, wn = E by using…

Q: The flat surface shown is submerged vertically in water. Find the fluid force against the surface.…

A: Weight density of water, WD = 9810 N/m3 Area of triangular surface, A = (base * height)/2 A=…

Q: Problem 1: You have been hired to design a family-friendly see-saw. Your design will feature a…

Q: The bridge construction company Z is facing problems with the mechanism of the crane, which it uses…

Q: (a) Determine the maximum shearing stress caused by a 4.6-kN • m torque T in the 76-mm-diameter…

Q: prove from first principles that the pressure at any point in a liquid is equal to hdg , where h…

Q: Two drums are connected by a belt. The drums each have mass 5.4 kg and radius 110 mm and it can be…

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

A: Given data P = 160 a = 290b = 190d = 25inner dia = 20 mmA is a point on the outer circumference.

Q: Q1 Methane (CH4) is supplied to a 20% excess air combustion reaction at a rate of 12 grams per…

A: Given: fuel CH4 for stoichiometric equation a = x+y/4 (CxHy fuel)

Q: Q3/ A car is moving along a straight line with the acceleration a- (12t- 3t) m/s', where t is in…

Q: A metal bar 5.0 m long extends by 0.05 mm when a tensile load is applied to it. The percentage…

Q: 750 lb Q.1: Determine the horizontal and 3 ft 3 11 vertical components of reaction on the member at…

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. Assume F = 710 N, a =…

Q: Problem 3: The wrench shown in the figure below is used to tighten a bolt at A. If the wrench does…

A: To determine the moment about A and also the reactions.

Q: in tensile test data, show step by step how to find stress and strain in aluminium

Q: A 32-tooth pinion has a module of 3 mm, rotates 2400 rpm, and drives an 800-rpm gear. Determine the…

Q: Car A is going Exst at 36 Hm/h and deceleration 3m)} B is going South at 30HM/ h and acalecabiom…

Q: PROBLEM 16.29 The 100-mm-radius brake drum is attached to a flywheel which is not shown. The drum…

Q: A spring mass system has a mass of 5 kg and k = 100N/m is pulled down a distance of 100 mm from the…

A: Given data:- K= 100kN/m Mass(m) = 5 kg Pull down distance = 100 mm. Find the static deflection ,…

Q: the indices for the direction shown below, based on the origin O.

Q: helpneeded in sketcting Several of the problems are not dimensioned. Use 5mm grid spacing and 10mm…

A: Please refer the following image for the required views as per requirement.

Q: A gear transmits 560 N of torque to a circular shaft having a diameter of 58 mm. A square key 13 mm…

A: Given Data The diameter of the shaft is: d=58 mm The torque transmitted by the gear is: T=560 N·mm…

Q: Q3 A) A shaft with 150mm in diameter and 1 m length is to be turned in an engine lathe. Cutting…

Q: A body is subjected to uniaxial tensile stress of 20 MPa in the y-direction as well as a temperature…

A: Find the strain in x ,y and z directions.

Q: Measurement systems plays a crucial role in industrial automation. Elaborate how the measurement…

A: given; measurement systems plays a crucial role in industrial automation. Elaborate how the…

Q: A Cascade refrigeration system using flash tank and intercooler is operating an evaporator with a…

A: Schematic Diagram

Q: 3-Consider a steady-flow Carnot cycle with water as the working fluid executed under the saturation…

Q: ) It starts from dwell and ends in am p) In section I the cam has a paraboli =) In section I from 0…

A: For the first section the cam has the parabolic profile as,Y=Aγ2+Bγ+C........0<γ<12The…

Q: The rod ABC is made of an aluminum for which E = 71.86 GPa. Knowing that P = 7.72 kNand Q = 48.58…

Q: A powerplant generates steam at a pressure of 8500 kPa and a temperature of 773 K, which is fed into…

A: Given data Pressure of steam entering turbine = 8500 kPa Temperature of steam entering turbine =…

Q: A car starts from rest and moves with a constant acceleration of 1.5 m/s' until it achieves a…

Q: Q2/ The ball is thrown off the top of the building. If it strikes the ground at B in 3 s, determine…

Q: 11. What do you understand by the terms (i) static and (ii) dynamic methods for determination of…

A: Phase diagrams are graphical depictions of the phases that exist in a certain alloy when it is…

Q: A manometer is used to measure the pressure of a gas in a tank. The fluid used has a specific…

Q: Find the stresses at point C. 1.5 m C 2.5 m 250 mm At 125 mm 1.5 m 50 mm 50 kN

A: Given Load, P = 50 kN/m Length, L = 2.5 m Find Stresses

Concept explainers

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.

Question

SHOW COMPLETE AND DETAILED SOLUTION.

PLEASE WRITE LEGIBLY.

GIVEN:

SOLUTION:

7. A wooden storage vat is 6 m in diameter and is filled with 7 m of oil, s = 0.8. the
wood staves are bound by flat steel bands, 50 mm wide by 6 mm thick, whose
allowable tensile stress is 110 MPa. What is the required spacing of the bands near
bottom of the vat, neglecting any initial stress?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A hemispherical window (or viewport) in a decompression chamber (see figure) is subjected to an internal air pressure of 85 psi. The window is attached to the wall of the chamber by 14 bolts. (a) Find the tensile force Fin each bolt and the tensile stress (T in the viewport if the radius of the hemisphere is 14 in. and its thickness is 1.25 in. (b) If the yield stress for each of the 14 bolts is 50 ksi and the factor of safety is 3.0, Find the required bolt diameter. (c) If the stress in the viewport is limited to 500 psi, find the required radius of the hemisphere.
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
: A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered into a lake (see figure). The compressed air in the tank is at a pressure of 24 psi (gage pressure when the tank: is out of the water). At what depth D0will the wall of the tank be subjected to a compressive stress of 90 psi?
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A large spherical tank (see figure) contains gas at a pressure of 420 psi. The tank is 45 ft in diameter and is constructed of high-strength steel having a yield stress in tension of 80 ksi. (a) Determine the required thickness (to the nearest 1/4 inch) of the wall of the tank if a factor of safety of 3,5 with respect to yielding is required. (b) If the tank wall thickness is 2.25 in., what is the maximum permissible internal pressure?
A wood stave pipe, 120 cm in inside diameter, is to resist a maximum water pressure of 1,200 kPa. If the staves are bound by steel flat bands (10 cm by 2.50 cm), find the spacing of the bands if its allowable stress is 105 MPa.\ Please explain the steps and formulas used.
A wood stave pipe, 120 cm in inside diameter, is to resist a maximum water pressure of 1,200 kPa. If the staves are bound by steel flatbands (10 cm by 2.50 cm), find the spacing of the bands if its allowable stress is 105 MPa
A spherical tank of diameter 1.2 m and wall thickness 50 mm contains compressed air at a pressure of 17 MPa. What is the value of tensile stress? (Assume E = 210 GPa, v = 0.29)
A thick-wall underwater pipe is placed at 20m below sea level. The pipe is carryingcompressed natural gas with pressure of 50 MPa. The pipe has 115mm outer diameter andmade of 316 stainless steel with yield strength of 205 MPa. The density of sea water could betaken as 1029 kg/m3. Find out:a) What is the resultant outer pressure acting on the underwater pipe? b) What is the minimum inner diameter to ensure the pipe does not yield?c) Sketch the variation of hoop and radial stress across the pipe wall, completed with stresslabelling. d) What is the resultant longitudinal stress of the pipe?
A thin metal pipe of mean radius R, thickness t and length L, has its ends closed and is full of water. If the ends are simply-supported, estimate the form of the distribution of shearing stresses over a section near one support, ignoring the intrinsic weight of the pipe. Answer: t = 2450 (RL/t) Show your solution
Calculate the diameter of a pressure vessel of thickness 0.04 m and the inside pressure is 20 mpa. Assume the permissible stress of the vessel is 100 mpa.
Problem :Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure Vessel = 10 Atmosphere. Longitudinal Stress (σL) = 200 MPa. Hoop Stress (σθ) = 150 MPa. Radial Stress (σR) = -50. Question :a) How thick is the pressure vessel if the Inner Diameter is D = 2 Meters? b) Check whether the pressure vessel is safe or not? c) Calculate the maximum shear stress with Mohr's circle? d) Check whether the pressure vessel is safe or not with Tresca yield criterion and compare it with von Mises yield criterion?