Please help, I promise to give good feedback. Please do not just guess. Thank you! 7. The concrete cover of the beam refers toa. From the outer edge of concreteto the surface of the reinforcingsteelc. From the outer edge of concreteto the neutral axisb. From the outer edge of concreted. Width of the beamto the center of the reinforcingsteel8. A reinforced concrete roof beam of a farm house should have a minimum concrete coverof_?a. 75 mmc. 20 mmb. 50 mmd. 40 mm39. It is the bar that accounts for the positive or negative moment in the fixed-fixed beam.a.Extra barsc.Cut barsb. Short barsd.All of the above10. For a continuous beam, the short bara. Terminates at the columnc.Extends through the columnd. None of the aboveb.Is bent 90 degrees at the column

As per Bartleby's guidelines we are supposed to answer only first question. Kindly repost other…

7. The concrete cover of the beam refers to a. From the outer edge of concrete to the surface of the reinforcing steel b. From the outer edge of concrete to the center of the reinforcing steel c. From the outer edge of concrete to the neutral axis d. Width of the beam

7. The concrete cover of the beam refers to a. From the outer edge of concrete to the surface of the reinforcing steel b. From the outer edge of concrete to the center of the reinforcing steel c. From the outer edge of concrete to the neutral axis d. Width of the beam

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.1P

See similar textbooks

Related questions

Q: Determine the largest shear force V (kips) that the member can sustain if the allowable shear stress…

Q: For a given sieve analyis: No. 4 - % finer 99%, for No. 200 -%finer 76. LL=60, PL= 32. Classify the…

A: Given % fine of different sieves Liquid limit, LL = 60 plastic limit, PL = 32 REQUIRED soil…

Q: The angle 150x100x100 mm is connected to the gusset plate. The size of weld is 8 mm and using E70…

A: P=ks×lw×σsσs=0.3×σy=0.3×393=117.9≈118Mpa400×103=0.7×8×lw×118lw=605.327mm

Q: The magnitude of the force P is 772 N. Determine the magnitude of the moment (Nm) of P about the…

Q: A permeability pumping test was carried out in a confined aquifer with the piezometric level before…

A: q =14.7m3/hr = 0.00408 m3/secr1= 17mr2= 33mb= 7.3mIt has been asked in the question to determine the…

Q: It is a drawing view in a building plan that shows for if there are changes in the elevation inside…

A: As per bartleby guidelines experts are allowed to solve only first three subparts. Please post…

Q: The volume and weight of a partially saturated clay sample are 185 cm3 and 362 g respectively. After…

Q: From the figure shown, H₁ = 0.60, H₂ = 0.90 m. and h = 0.45 m. The sand has a saturated unit weight…

Q: What is the nominal tensile strength of the member based on yielding a. 240 kN c. 150 kN b. 250 KN…

Q: Situation 17. A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is…

Q: A rectangular concrete slab, 3 m x 4.5 m, rests on the surface of a soil mass. The load on the slab…

Q: A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

A: Given: The width of the beam is 250 mm. The depth of the beam is 500 mm. The diameter of the bottom…

Q: |R2 Im rip RON.m पा 조 wh W/NGOL 2m

Q: What is the area of the ellipse with vertices (0,±7) and foci (0,±3)?

A: Given: The vertices are (0, ±7). The foci are (0, ±3).

Q: 111. A column in an agricultural structure has the following dimensions: b = 0.3 x 0.3, 6-16mm…

Q: Based on the sieve analysis a soil has % finer for the following sieves: No. 10- 84% ; No. 40- 71%…

Q: It is a man made materials made from various types of polymers used to enhance, augment and make…

A: Answer:- GEOSYNTHETICS Geosynthetics are human-made materials which are made from the various types…

Q: The column is constructed from high-strength concrete and A-36 steel reinforcing rods. If it is…

Q: answer

Q: Consider a beam as shown below. A 29. What is the reaction at A. a. 20.79 KN b. 12.47 kN 30. What is…

Q: Maria was trying to test the braking ability of her car determined that she needed 5.64m more to…

A: Solution-The Given data is shown below, Grade of downhill = 5% Grade of uphill = 3% The extra…

Q: A carry concrete slat in the flooring of a swine housing is designed to carry swine up to 225 kg.…

Q: A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8 m long,…

Q: Determine reaction at the support and the forces of each members of the truss shown. Use joint…

Q: diagram

A: Shear force diagram refers to the internal forces alone. Bending moment diagram refers to the moment…

Q: A circular area having a radius of 3 m carries a uniformly distributed of 90 kPa is applied to the…

Q: Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions…

A: Given data f'c = 21MPa fy = 420Mpa a Es=2×105MPaes=fyEs=4202×105=2.1×10-3 So…

Q: А 240 kN 12m/7 400 KN B 12m 600 KN 12 m E F 12m-fill

Q: From the figure shown, H₁ = 0.60, H₂ = 0.90 m. and h = 0.45 m. The sand has a saturated unit weight…

Q: What flow can be expected in a 1.2m wide rectangular, cement-lined channel (n=0.015) laid on a slope…

A: Given data width of channel (B) = 1.2 m depth of flow (y) = 0.6 m Slope (S) = 4m in 10km n = 0.015…

Q: Determine the allowable permissible Twisting moment, T (N-m) as shown in the figure: Tst ≤ 83 MPa…

Q: Show

Q: A PL40 mm X 250 mm (smaller member) is connected to a gusset plate (bigger member) as shown. The…

Q: Calculate the effective net soil bearing capacity of the soil. = [q] kPa (one decimal place)

A: Given Data:D.L=145kN/mL.L=215kN/mγsiol=16kN/m3γconc=24kN/m3qa=200kpafc=28mpafy= 420mpa

Q: A spiral column carries a service dead load of 1000 kN and a service live load of 900 kN. fc' = 27.5…

Q: A short rectangular column 300 mm on one side and 400 mm on the other side. It is reinforced with…

Q: Using the method of joints, determine the force in each member of the truss shown below (solve for…

Q: A permeability pumping test was carried out in a confined aquifer with the piezometric. level before…

A: Our aim is to determine the depth of water at the farthest observation well. So, let's get started…

Q: From the figure shown, H₁ = 0.60, H₂ = 0.90 m. and h = 0.45 m. The sand has a saturated unit weight…

Q: If the natural void ratio of the soil was 0.54, determine the specific gravity of the solid.

Q: A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

A: The maximum safe allowed moment that a beam can carry is determined by its moment carrying capacity.…

Q: DRAW THE CORRESPONDING MOMENT DIAGRAM OF THE BEAM. 12 kN/m 96.5 3 m 1.5m1m1m 51.5 V-Diagram (kN)…

Q: a cylindrical vessel has 0.5m diameter and 1m height rotates at 10rad/s. initial height of Mercury…

Q: Names Course: Fig 2 A 20 TR₁ 100 N/ I Answer 120N-m 10 R2 N Datel Timet Draw the shear and moment…

Q: A contractor has made regular modest financial payments to one of your coworkers. They are less than…

A: Given: A contractor has made regular modest financial payments to one of your coworkers. They are…

Q: A catwalk of an onion cold storage building is designed for a uniform dead load of 1.6 kPa and a…

Q: Calculate the critical slenderness ratio with buckling about strong axis. calculate the critical…

Q: Determine the shear value when x = 5m (from the left) for the beam shown Where: P1 = 51kN; P2 = 42…

Q: example of longitudinal critical frame analysis (cantilever method) varignons theorem

A: Hey there Here I will provide an example of analysis of cantilever method in detailed. So, within…

Q: The following offsets were taken at 20 m intervals from a survey line to an irregular boundary line…

Concept explainers

Introduction to Engineering Design

Students are often confused with engineering and design. The term engineering design has two words with different meanings, engineering, and design. The term engineering implies applications of laws and principles of science to design and analyze physical structures and components. In civil engineering, students apply the concept of physics and chemistry to design and build structures and buildings. In engineering disciplines, the term design means determining the dimensions, loads, and associated influences on the component due to the applied loads such as stresses and deformations. The estimation of such parameters is crucial to make the component or structure foolproof.

Question

Please help, I promise to give good feedback. Please do not just guess. Thank you!

7. The concrete cover of the beam refers to
a. From the outer edge of concrete
to the surface of the reinforcing
steel
c. From the outer edge of concrete
to the neutral axis
b. From the outer edge of concrete
d. Width of the beam
to the center of the reinforcing
steel
8. A reinforced concrete roof beam of a farm house should have a minimum concrete cover
of_?
a. 75 mm
c. 20 mm
b. 50 mm
d. 40 mm
39. It is the bar that accounts for the positive or negative moment in the fixed-fixed beam.
a.
Extra bars
c.
Cut bars
b. Short bars
d.
All of the above
10. For a continuous beam, the short bar
a. Terminates at the column
c.
Extends through the column
d. None of the above
b.
Is bent 90 degrees at the column

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength pMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc': 28 MPa and fy = 413.70 MPa. 750 mm T175 mm 1000 mm 9-36 mm diameter bars 350 mm
III. Locate the centroid of the composite area below. Y 50 80 mm, mm R=50mm 250mm R=65mm -- X 50 50 mm mm
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with d-20-mm-dismeter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is M0 mm and at the bottom is 70 mm. Use concrete strength r'e-21 MPa und steel yield strength fy 415 MPa for 20- mm bars and fy= 275 MPA for 16 mm bars Detenmine the design moment capacity n kN m of the beam in negative bending. A 40.06 O45.07 C. 42.70 D47.55
A doubly reinforced concrete beam of size 250 mm x 500 mm overall depth is reinforced with 2-12 mm dia. bars in compression zone and 3-20 mm dia. bars in tension zone, each at an effective cover of 40 mm. The grade of concrete and steel are M20 and Fe415 respectively. The strain in compression steel will be [Take stress in compression steel as 345 MPa]
Situation: A beam has a width of 300 mm and total depth of 600 mm strength f'c-36 MPa. Steel yield strength fy=415 MPa The section is to be reinforced for tension only and the effective concrete cover is 65 mm. Which of the following most nearly gives the value of our balanced steel ratio? a. 0.00370 b. 0.03456 C. 0.02860 d. 0.03522 Which of the following most nearly gives the value of our balanced distance of the cuter most fiber of compression fiber to our neutral axis? a. 313.256 mm b. 354.68 mm C. 333.333 mm d. 322.435 mm Which of the following most nearly gives the value of our balanced depth of compression block? a. 248.412 mm b. 266.2676 mm C. 301.478 mm d. 281.261 mm
A 300 mm X 450 mm exterior beam is reinforced with 2 – Ø20 mm and 1 - Ø25 mm bars on the first layer of tension reinforcement (larger bar is at the middle), 2 tension reinforcement, 3 – Ø25 mm for compression reinforcement and Ø12 mm for stirrups. From analysis the depth of the tension zone is 344 mm, if the tension steel has a yield strength of 420 MPa and the compression steel has a yield strength of 414 MPa. Determine the following using all the NSCP provision (larger bar always governs the spacing) to check and layout the beam: Ø25 mm on the second layer of - A. The compressive stress in the concrete B. The depth of compression block C. Ultimate Moment Capacity of the beam
The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength oMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc' = 28 MPa and fy = 413.70 MPa. 750 mm T175 mm 1000 mm 9-36 mm dibmeter bars 350 mm dooo
Determine the values of the distance cfrom the extreme concrete corppression fibers to the neutral axis, andr, for the beam shown in the following Figure fy 60,000 psi and fc 3000 psi. 0.003 21 in d-c 389 bars 3.00 in) = (0.003) 12 in Select one: a. 6.90 in, 0.0061 b. 6.25 in, 0.0069 c. 7.50 in, 0.0085 d.5.93 in, 0.0076
compute the flexural stressesin the concrete and steel for the beams shown using the transformed-area method.
3. A reinforced rectangular concrete beam having a width of 300 mm, effective depth of500 mm, fc’ = 24 MPa, fy = 415 MPa, 4 - 28 mmɸ, d’ = 65 mm. Present the following (a) actual steel ratio (b) maximum steel ratio (c) a(d) c (e) check if steel yields (f) ?steel(g) type of failure (h) reduction factor (i) moment capacity
A rectangular bear has a wish of 300mm and a total depth of 650mm , calculate the area of steel reinforcement repral Take, M. 360kN.m f30 MPa and , 400MP