A catwalk of an onion cold storage building is designed for a uniform dead load of 1.6 kPa and a uniform live load of 3.2 kPa. HANGER ROD PLATFORM 2.7 m 1.2 m 7. Determine the dead loads carried by one of the hanger bars a. 5.2 kN c. 2.6 kN d. 6.2 kN b. 1.6 kN 8. Determine the live loads carried by one of the hanger bars 10.4 kN a. c. 5.2 KN d. 4.6 kN b. 3.2 kN 9. Determine the load combination of one of the hanger bars a. 22.8 kN C. 11.4 kN b. 4.8 kN d. 7.8 kN

A catwalk of an onion cold storage building is designed for a uniform dead load of 1.6 kPa and a uniform live load of 3.2 kPa. HANGER ROD PLATFORM 2.7 m 1.2 m 7. Determine the dead loads carried by one of the hanger bars a. 5.2 kN c. 2.6 kN d. 6.2 kN b. 1.6 kN 8. Determine the live loads carried by one of the hanger bars 10.4 kN a. c. 5.2 KN d. 4.6 kN b. 3.2 kN 9. Determine the load combination of one of the hanger bars a. 22.8 kN C. 11.4 kN b. 4.8 kN d. 7.8 kN

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.15P

See similar textbooks

Similar questions

A two story office building has interior column spaced at 6.7m apart in two perpendicular directions. If the flat of the roof live loading is allowed to be reduced live load of an interior column located at the ground floor level. Using NSCP 2010, determine the following: a.) basic roof live load in kPa b.) roof live load in kN forthe column c.) basic floor live load due to occupancy in kPa d.) reduced floor live load in kN for the column e.) total live load supported by the ground floor column
A building wall consists of exterior stud walls with brick veneer and 13 mm fiberboard on one side. If the wall is 4 m high, determine the load in kN/m that it exerts on the floor. From Minimum Design Dead load, For stud wall with brick veneer, w = 2.30 kN/m^2 and for fiber board, w = 0.04 kN/m^2.
A wall footing 1 m wide carries a uniform load of 300 kN/m of wall length. Soil weights 16 kN/m^3.Using the influence chart, compute the total vertical increment of the loads at a depth of 3 m from the edge of the strip in kN/m. a. 48 b. 60 c. 156 d. 108
a) What will be the designed section of a pier cap (Let b = h/2) for a simply supported 25-meter span concrete bridge with a solid one-way slab of 450 millimeters? b) If the concrete unit weight = 23.60 kN/m3 , what is the uniform dead load of the bridge cap, in Newtons per meter?
PS. triangular load is from 25 kN/m to 0 kN/m
If the motor exerts a constant force of 300 N on the cable, determine the speed ofthe 20-kg crate when it travels s = 10 m up the plane, starting from rest. The coefficient of kineticfriction between the crate and the plane is μk = 0.3. PWE
The tower crane is used to hoist a 2-Mg load upwardat constant velocity. The 1.5-Mg jib BD and 0.5-Mg jib BChave centers of mass at G1 and G2, respectively. Determinethe required mass of the counterweight C so that the resultantmoment produced by the load and the weight of the towercrane jibs about point A is zero. The center of mass for thecounterweight is located at G3.
The channel section carries a uniformly distributed load totaling 6W and two concentrated loads of magnitude W. Determine the (a) location of the neutral axis from the bottom, (b) the moment of inertia about that axis, (c) the maximum allowable value for W if the working stress are 4.0 MPa in tension, 8.0 MPa in compression, and 2.4 MPa in shear.
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa
Compute σz in kPa at point A due to the two-line loads shown in figure.
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ,compression bars As’ = 2-28 mmØ, d’ = 60 mm. Fc’ = 30 MPa and fy = 345 MPa Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN Please answer asap.
at support D, what is the value of negative shear? a. -40 kN b. -50 kN c. -55 kN d. -60 kN at support D, what is the value of positive shear? a. 20 kN b. 25 kN c. 30 kN d. none of the above