7. The devices that convert serial to parallel and parallel to serial are called?a) Serializer/Deserializerb) Transmission convertersc) Multiplexerd) Preemphasizer8. Find out the resolution of 8 bit DAC/ADC?a) 562b) 625c) 256d) 2659. Non-linearity in the output of converter is expressed ina) None of the mentionedb) Percentage of reference voltagec) Percentage of resolutiond) Percentage of full scale voltage10.How many equal intervals are present in a 14-bit D-A converter?a) 16383..>A 14-bit D-A converter has 2"-1 equal interval =214-1=16384-1=16383.b) 4095c) 65535d) 102311.Find the resolution of a 10-bit AD converter for an input range of 10v?a) 97.7mvb) 9.77mvc) 0.977mvd) 977mv12.A good converter exhibits a linearity errora) Less than or equal to (1/2)LSBb) Greater than equal to (1/2)LSBc) Greater than or equal to (1/2)LSBd) None of the mentioned

As per our guidelines we are supposed to answer first 3. Kindly repost other questions separately.…

7. The devices that convert serial to parallel and parallel to serial are called? a) Serializer/Deserializer b) Transmission converters c) Multiplexer d) Preemphasizer 8. Find out the resolution of 8 bit DAC/ADC? a) 562 b) 625 c) 256 d) 265 9. Non-linearity in the output of converter is expressed in a) None of the mentioned b) Percentage of reference voltage c) Percentage of resolution d) Percentage of full scale voltage

7. The devices that convert serial to parallel and parallel to serial are called? a) Serializer/Deserializer b) Transmission converters c) Multiplexer d) Preemphasizer 8. Find out the resolution of 8 bit DAC/ADC? a) 562 b) 625 c) 256 d) 265 9. Non-linearity in the output of converter is expressed in a) None of the mentioned b) Percentage of reference voltage c) Percentage of resolution d) Percentage of full scale voltage

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

1. Given the 8 bit hex number 0x5E, what smallest hex value would you have to add to set the Overflow flag? 2. Given the 8 bit hex number 0x6E, what smallest hex value would you have to add to set the Carry Flag? Please give detailed explanation on how to solve.
T/F. The conversion from parallel to serial data transmission and vice versa takes place inside the interface circuits.
LIST P = 16F877AUsing INCLUDE "P16F877A.INC" and PWM (Pulse Width Modulation), write the microprocessor code that enables the fan to operate at 80% if the button on the 5th bit is pressed, and 30% if the button on the third bit is pressed.
In this exercise you are to construct an ALU with the following specification: • The ALU takes 3 different 32-bit inputs: A, B, C; and has one 32-bit output: D. • The ALU supports 7 different operations: – A + B (addition) – A - B (subtraction) – MAX(A,B,C) – MIN(A,B,C) – A & B (bitwise AND) – B & C (bitwise AND) – (A + B) & C (addition followed by bitwise AND) To construct this ALU you will follow a modular design. Assume you have an unlimited number of the following gates and combinational circuits at your disposal, but no others: • 2-arity AND gate, • 2-arity OR gate, • NOT gate, • 2-way MUX, • bit-wise AND circuit: it takes two 32-bit inputs and has a 32-bit output which is the bit-wise AND of its inputs. • 32-bit ADDER: it takes two 32-bit inputs, a 1-bit control signal, and has a 32-bit output. If the control signal is 0, the circuit outs the sum of its inputs. If the control signal is 1, the circuit outputs the difference of its inputs. The inputs and outputs are…
Build C program to perform task below. Design its circuit in Proteus. State your observations.a) Make Port D produce 5V. Use bit addressable instructions.b) Make pin RB7, RB5, RB3 and RB1 ON and other Port B pins OFF. Use byte addressableinstruction.c) Make RE0, RA1, RB2, RC3 and RD4 HIGH.result discussion conclusion
13.a) Design a 4 bit arithmetic unit with two selection variables s0 and s1 and two n-bit data inputs A&B and input carry Cin s1 s2 Cin=0 Cin=10 0 F=A F=A+10 1 F=A+B F=A+B+11 0 F=A+B’ F=A+B’+11 1 F=A-1 F=A b) Explain the design of an accumulator. need complete solution...thanks
3- What is the difference between: a- MOV BX,[1234H] and LEA BX,[1234H] b- LDS AX,[200H] and LES AXX,[200H] 4-Use MOV to load address of memory MEM1.
How does the ALU handle overflow and carry in arithmetic operations? Provide an illustration.
Assume x goes to $s0, y goes to $s1, and z goes to $s2. Convert the following C code to MIPS. Use temporary registers ($t0, $t1, etc.) when appropriate. z = x - 7;
Assume x goes to $s0, y goes to $s1, and z goes to $s2. Convert the following C code to MIPS. Use temporary registers ($t0, $t1, etc.) when appropriate. y = y + 1;
please typed not picture Implement single port 128×8 RAM module using VHDL with synchronous read/write operations. and Show waveform by quartus.
5. For in-use inodes, each address in use is also marked in use in the bitmap. If not, print ERROR: address used by inode but marked free in bitmap.