8-3. A horizontal force of P 100 N is just sufficient to hold the crate from sliding down the plane, and a horizontal force of P 350 N is required to just push the crate up the plane. Determine the coefficient of static friction between the plane and the crate, and find the mass of the crate. %3D 30 Probs. 8-1/2/3

8-3. A horizontal force of P 100 N is just sufficient to hold the crate from sliding down the plane, and a horizontal force of P 350 N is required to just push the crate up the plane. Determine the coefficient of static friction between the plane and the crate, and find the mass of the crate. %3D 30 Probs. 8-1/2/3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the center of gravity of the stacked tables is at G, and the stack weighs 100 lb, determine the minimum force P that the child must apply to the stack to cause a motion. The coefficient of static friction at A and B is μs = 0.3. The tables are secured to each other.
Determine the maximum force P that can be applied without causing movement of the 250 lb homogeneous block. The coefficient of static friction between the block and the floor is 0.4 and between the 4 ft diameter wheel and the rope is 0.2.
If the center of gravity of the stacked tables is at G, and the stack weighs 100 lb, determine the smallest force P the boy must push on the stack in order to cause movement. The coefficient of static friction at A and B is µs = 0.30. The tables are locked together.
reinforced concrete T-beam has an effective depth of 600 mm and is reinforced at the bottom with steel area of 4926 mm2. The web width is 300 mm and has a flange thickness of 100 mm. The beam has a span of 6 m and has a spacing center to center equal to 1.8 m. ??′=21 MPa ??=415 MPa. Determine the following:a. Effective width of the flangeb. Depth of the compression blockc. Nominal moment capacity of the beam
A shaft 70 mm in diameter is being pushed at a speed of 400 mm/s through a bearing sleeve 70.2 mm in diameter and 250 mm long. The clearance, assumed uniform, is filled with oil at 20 C with v=0.005 m^2/s and sp.gr.=0.9. Find the force exerted by the oil in the shaft.
Two 10° wedges of negligible weight are used to move and position the 400-lb block. Knowing that the coefficient of static friction is 0.25 at all surfaces of contact, determine the smallest force P that should be applied as shown to one of the wedges.
A 12° wedge is used to split a log. The coefficient of static frictionbetween the wedge and the wood is 0.40. Knowing that a force P ofmagnitude 3.2 kN was required to insert the wedge, determine themagnitude of the forces exerted on the log by the wedge after it hasbeen inserted.
If the center of gravity of the stacked tables is at G,and the stack weighs 100 lb, determine the smallestforce P the boy must push on the stack in order tocause movement. The coefficient of static friction atA and B is μs = 0.3. The tables are locked together. P = _____________
A uniform 50-kgf board rests on rough supports located at A and B in the figure. Thefriction coefficient μs=0.60 on both contact surfaces. If a man weighing 80 kgfpulls on the rope with a force of 40 kgf, determine:a) The angles "min" minimum and "max" maximum for which the system is in equilibrium.b) The minimum coefficient of friction that must exist between the soles of the man's shoes andthe soil for each of the cases in section a.
A reinforced concrete beam has a width of 425mm and an effectivedepth of 900mm. The longitudinal bars at compression side are 4-25mm dia. and 2layers of 4-32mm dia. at tension side. Concrete strength f’c=27.60 MPa and fy=420.4) Calculate the Transformed moment of Inertia.5) Calculate the moment capacity of the section.6) Calculate for the safest uniform load that can carry by the beam if ihas a lengthof 10m.
Determine support reaction. P=800 lb , a=5 ft b=9 ft
Determine support reaction. Given a=5 m b=10 m P=30 KN