The cantilever beam as shown in figure of span 5 m is supported by a 2 m long, 2 mm diameter wire CB. Determine the force (in kN) developed in the wire due to loading if the flexural rigidity of the beam El = 5000 kNm2 and the Young's modulus of the wire is 200 GPa. (Answer upto two places after decimal) C 5 kN 2 kN/m AD A B 4m- 1m- 2m

The cantilever beam as shown in figure of span 5 m is supported by a 2 m long, 2 mm diameter wire CB. Determine the force (in kN) developed in the wire due to loading if the flexural rigidity of the beam El = 5000 kNm2 and the Young's modulus of the wire is 200 GPa. (Answer upto two places after decimal) C 5 kN 2 kN/m AD A B 4m- 1m- 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 2 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c = 21 MPa, long bar fy = 415 MPa, calculate: Using a T-beam geometry, determine the required amount of flexure bars for maximum ultimate bending. = [As] sq.mm (whole number)
A 5.5m simple beam carries a uniform ultimate load Wu. The beam is laterally supported and has compact section. The properties of the section are: rx=105.16mm, ry=22.2mm, Sx=308000mm^3, Sy=35000mm^3, Zx=357000mm^3, Zy=55000mm^3, and Fy=248MPa. Calculate the ultimate load capacity Wu of the beam in KN/m considering flexure. Express your answer in 3 decimal places.
The cantilever beam consists of a rectangular structural steel tube shape [E = 205 GPa; I = 90 × 106 mm4]. For the loading shown, determine the beam deflection at point B.Assume wAB = 45 kN/m, wBC = 25 kN/m, P = 30 kN, Q = 40 kN, LAB = 2.1 m, LBC = 3.1 m.
A beam is subjected to equal 11 kip-ft bending moments. Assume t1 = t2 = tw = 1 in., d = 14 in., b1 = 3 in., and b2 = 5 in. The cross-sectional dimensions of the beam are illustrated. Determine: (a) the distance to the centroid (measured from the bottom), the moment of inertia I about the z axis, and the controlling section modulus S about the z axis.(b) the bending stress at point H (positive if tension, negative if compression).(c) the bending stress at point K (positive if tension, negative if compression).(d) the maximum bending stress produced in the cross section (positive if tension, negative if compression).
A reinforced concrete beam has a width of 425mm and an effectivedepth of 900mm. The longitudinal bars at compression side are 4-25mm dia. and 2layers of 4-32mm dia. at tension side. Concrete strength f’c=27.60 MPa and fy=420.4) Calculate the Transformed moment of Inertia.5) Calculate the moment capacity of the section.6) Calculate for the safest uniform load that can carry by the beam if ihas a lengthof 10m.
The beam as shown in Figure has a rectangular section with a depth of 250mm and width of 40mm. In addition to the point loads, the beam is also subjected to UDL having a magnitude of 176N/m acting at span from point B to free end. Calculate the slope and deflection at free end. Assume E = 200GPa. (Where P =88 KN )
For the W410x100 steel beam shown below, the distributed load along AB is a= 11 kN/m, the concentrated load at Point C is b = 13 kN. Generate the shear force diagram and calculate / input the shear force developed on the cross section at the middle of BC: V=__ kN. Calculate your answer to 1 decimal place.
A tied column 300 x 350 mm as shown in the figure is reinforced with 6 pieces steel barshaving fy = 414 MPa and fc’ = 21 MPa as shown in the figure. The column is to resist a factoredload of 1200 kN and factored moment of 280 kNm. Using the interactiondiagram, determine the following:a. eccentricity, eb. steel ratioc. diameter of the steel bars
A concrete beam has a cross sectional area of 275mmwidth and 150mm height for the upper flange. While thelower flange has 450mm width with a 150mm height. If theflange has length of 225mm while 200mm width,determine the centroid and the moment of inertia of thegiven structure. answer this ASAP. Please thank you
A distributed loading of q(x) = (10x1/2 + 160x + 10) Pa acts over the top surface of the beam of span length 10m. The width of the surface loading on the beam is 0.5m. Sketch the loading and then determine the magnitude and location of the equivalent resultant force, FR.
Compute the bending stresses in the beam shown, f'c = 28 MPa Es=200000MPa M=165 kN-m
The simply supported beam shown consists of a W410 × 60 structural steel wide-flange shape [E = 200 GPa; I = 216 × 106 mm4]. For the loading shown, determine the beam deflection at point B. Assume P = 85 kN, MC = 65 kN·m, LAB = 2.3 m, LBC = 4.6 m.