8- A transformer, when tested on full-load, is found to have Cu loss 1.8% and reactance drop 3.8%.Calculate its full-load regulation (i) at unity p.f. (ii) 0.8 p.f. lagging (iii) 0.8 p.f. leading.
Q: Find the Fourier Series of the function. f(x)= -K if -2<x<0 1-K k if 0<x<2 - A sinusoidal voltage &…
A: Solve the first question, unless the student has asked for a specific question to be solved, subject…
Q: Ck={0,0,0,1,0,1,0,0}
A:
Q: Characteristics curve of a single phase induction motor (open and closed circuit )
A: We need to draw characteristics curve of a single phase induction motor (open and closed circuit ).
Q: The flux density at a point in space given by B = 4xāx+2kyāy+8ã Wb/m^2. The value of constant * must…
A: In this question flux density is given....We have to find out unknown value of k...
Q: The open loop transfer function of a unity feedback system is given by (s+1) G(s)= (s+2)(s…
A: In this question we need to find a centroid and choose a correct option.
Q: QUESTION 13 The resistance of the Armature's conductor coil(s) in most motors is: quite high,…
A: The resistance of armature conductors are very low of range 2 to 4 ohm the reason behind the low…
Q: 11.40 In a balanced three-phase wye-wye system, the source is an abc-sequence set of voltages and V…
A: In this question, We need to determine the load impedance if line current and voltage in the phase…
Q: A small DC machine has a torque constant of 0.47NM/A and an armature resistance of 4 ohms. It is…
A:
Q: QUESTION 10 As a motor increases in rotational velocity to 100% of the rated RPM, the CEMF induced…
A: In DC motor CEMF stands for counter emf and it is also called back EMF which is given by CEMF = K.…
Q: A system is represented by the block diagram shown in Figure 2. x[n] + y[n] -3 D + 2 D Figure 2:…
A:
Q: 2. In a three phase system the named voltage is defined as the Line to ground voltage Phase to…
A: There are certain notations we use to refer physical quantity in power system and it is a type of…
Q: Determine the frequency responses of the following systems. Problem 2.4 (a) y(t) = r(t-1)
A: As per our guidelines we are supposed to be answer the first question only. Kindly repost the other…
Q: If the input x(t)= e-³tu(t) and the output y(t) = cos3t, find h(t) where the convolution y(t) =…
A: The solution is given below
Q: QUESTION 4: Consider an idealized class-B output stage shown below. The output stage is to deliver…
A: Given Consider an idealized class-B output stage shown below. The output stage is to deliver 42 W of…
Q: A spherical capacitor having a radius of 5cm and 5.5cm for positive and negative conductor…
A:
Q: Solve for Vo if v1 =10V and v2=5V. Vo = 100 ΚΩ Μ 100 ΚΩ ww V-N 20 ΚΩ w V₁ + 20 ΚΩ 741 Volts. Vo
A: The solution is given below
Q: Example1/ An open wire T-L with R=10 K/Km,L=3.7 mH/km, C-8.3x 10-⁹F/Km and G=0.4x 10-6U/Km, find…
A: The solution is given below
Q: Draw the circuit diagram of power system layout with three phase CT and three phase PT.
A: Electrical Transformers can be used as Measuring devices when used in specific configuration. These…
Q: An air-cored choking coil is subjected to an alternating voltage of 100 V. The current taken is 0.1…
A:
Q: what is the stable voltage range at the output of figure b? 1KQ Vpp = 20v AC Voltage IDEAL DIODE 3V…
A:
Q: A system with unity feedback has an open-loop transfer function G(s) = K/[(TS + 1)s], where T is the…
A:
Q: N-channel enhancement MOSFET control voltage is applied at the controlling the current that is. d —…
A: We need to select correct option for given statement .
Q: For the circuit shown below find Av, Ai, Ro, Ri.
A: The required parameters can be calculated by using DC and AC analysis of amplifier circuit.
Q: 1)))))For the above circuit, determine: a) The value of a resistance Rv, so that there is the…
A: In this question, We need to determine the The value of a resistance Rv for maximum power transfer…
Q: Digit keys +5 V 1 kg For switch bounce Q >T OS ō tp-20 ms Pull-up resistor for each input 74LS147…
A: A basic logic circuit of a keyboard encoder must have 4 outputs and 10 parts of inputs (0 to 9 ). A…
Q: Given ID = 4 mA at VGS = -2 V, determine IDSS if VP= -5 V.
A: In this question, We need to determine the Saturation drain current IDSS ?
Q: Draw the Vs and is as a function of time when the switch on at t=0 R3 S2 Vs Rr=00 Ro -E к
A: Here we have got a DC source voltage and a purely resistive circuit. Since there is no inductor and…
Q: P5.2 Determine the digital output of a 10-bit A/D convertor with 0 to 5 V analog voltage range if…
A:
Q: Consider a continuous-time system with input x(t) and output y(t) given by y(n) = 4x²(n-2) + 1. This…
A: In this question we need to choose a correct option
Q: y(n)= y(n-1) - 0.21y(n-2) + 3x(n) + 2x(n-2) a. find zero input response , yzi(k) when the inintial…
A: The solution is given below
Q: Find the Fourier Series Representation of f(eitheta) = 1/13-12 cos(theta
A:
Q: 3dB frequency wo in radians per second. R R VIN Vo Rb 1.2K Ra 1.0K C 0.4uf .1xF R =1000 2 = 4 KR
A:
Q: 01 C' 1 0 1 23 2 0 1 4-to-1 MUX is BC 2-to-1 MUX B FO F1 0 1 2-to-1 MUX A F LL
A: given here a logic circuit asked to write the output expression for the logic function. we know that…
Q: A system is represented by the below transfer function: 3 G(s) = 2s² + 6s + 10 Sketch the Bode plot…
A: The transfer function of a system is given as Gs=32s2+6s+10.
Q: What values of Rs will ensure that the output voltage is stable at 10V
A:
Q: Given the circuit below, find the minimum and maximum output voltage after the filter capacitor,…
A: The circuit can be redrawn as Time constant of the circuit will beζ=1.2k×10mζ=12secTime period of…
Q: (c) Design a 3-bit synchronous counter using falling edge-triggered T flip-flops. The counter…
A: Using excitation table we filled state transition table. circuit entering 100 state analysis is done…
Q: When a 100-kVA single-phase transformer was tested in this way, the following data were obtained: On…
A: In this question we need to find efficiency of transformer for given loading conditions.
Q: consider the following LTI discrete-time system; y[n]=y[n-1]-0.21y[n-2]+3x[n]+2x[n-2]. find zero…
A: The solution is given below
Q: PROBLEM 2. Find I single prime; I. double prime; IL R$30 Ω Xc60 E₁ = 30 V 230° XL voo +1₁ 8 Ω I= E₂=…
A: Current: It is the time rate of the change of the charges. When potential is created across the…
Q: 11.63 A balanced three-phase source serves the following loads: Load 1: 60 kVA at 0.8 pf lagging…
A: The solution is given below
Q: Draw the voltage vm as a function of time when Zo = Ro = 500 for figure shown www 50Ω S3 个 502 ↑ Vs…
A: In this question we need to draw Vm as a function of time
Q: 5- A single-phase transformer, working at unity power factor has an efficiency of 90 % at both…
A:
Q: Q2 TAI RL 10 Q1 sig If sig = 3.3V, Reps (ON) B2 = 100 m_s2 and RRRS (ON) Q1 = 50 ms2 then Vout = V…
A: Here both nmos and pmos are on . Current is calculated from equivalent circuit . RDS on of bith pmos…
Q: Two identical three-phase wye connected alternators A and B share equally a load of 10MW at 33kV and…
A:
Q: Find total current
A: Given circuit,
Q: How far does the electron of a hydrogen atom have to be removed from the nucleus for the force of…
A: Solution -
Q: A capacitive sensor in air measures 4.0 µF. It measures 10.0μF when placed in a non-conducting…
A: Given data, Capacitance in air, Ca=4.0 μF Capacitance in non-conducting liquid, Cl=10.0 μF
Q: To put it another way: A BTS broadcasting information with 10 W of output power at 1800 MHz can only…
A: BTS broadcasting It is the type of base transceiver station, in which a fixed radio transceiver is…
Q: Find the laplace transform of f(t) = 2t4 - 3e³t + 10 cos 2t F (s) =…
A:
Step by step
Solved in 2 steps with 1 images
- Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) FalseIn developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) FalseA three-phase transformer is rated 1000MVA,220Y/22kV. The Y-equivalent short-circuit impedance, considered equal to the leakage reactance, measured on the low-voltage side is 0.1. Compute the per-unit reactance of the transformer. In a system in which the base on the high-voltage side of the transformer is 100MVA,230kV what value of the per-unit reactance should be used to represent this transformer?
- For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
- A single-phase two-winding transformer rated 90MVA,80/120kV is to be connected as an autotransformer rated 80/200kV. Assume that the transformer is ideal. (a) Draw a schematic diagram of the ideal transformer connected as an autotransformer. showing the voltages, currents, and dot notation for polarity. (b) Determine the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of the kA rating is transferred by magnetic induction?For developing per-unit equivalent circuits of single-phase three-winding transformer, a common Sbase is selected for all three windings and voltage bases are selected in proportion to the rated voltage of the windings (a) True (b) FalseConsider the oneline diagram shown in Figure 3.40. The three-phase transformer bank is made up of three identical single-phase transformers, each specified by X1=0.24 (on the low-voltage side), negligible resistance and magnetizing current, and turns ratio =N2/N1=10. The transformer bank is delivering 100 MW at 0.8 p.f. lagging to a substation bus whose voltage is 230 kV. (a) Determine the primary current magnitude, primary voltage (line-to-line) magnitude, and the three-phase complex power supplied by the generator. Choose the line-to-neutral voltage at the bus, Va as the reference Account for the phase shift, and assume positive-sequence operation. (b) Find the phase shift between the primary and secondary voltages.
- Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of 240 V and at 0.8 posr factor lagging. Neglect the transformer exciting current. (a) Determine the input terminal voltage of the transformer on the high-voltage side. (b) Sketch the corresponding phasor diagram. (c) If the transformer is used as a step-down transformer at the load end of a feeder whose impedance is 0.5+j2.0, find the voltage VS and the power factor at the sending end of the feeder.A 23/230-kV step-up transformer feeds a three-phase transmission line, which in turn supplies a 150-MVA,0.8 lagging power factor load through a step-down 230/23-kV transformer. The impedance of the line and transformers at 230kVis18+j60. Determine the tap setting for each transformer to maintain the voltage at the load at 23 kV.