8 m/sec in the direction of jet. Find the forceexerted on the plate in the direction of the jet,power and efficiency of the jet. Assume59. Ajet of water of 75 mm diameter strikes a curvedvane at its center with a velocity of 20 m/sec.The curved vane is moving with a velocity oftheplate to be smooth.nswer

Answered: Image /qna-images/answer/dad213d3-30f1-4e2b-8957-b7937360cc6c.jpg

8 m/sec in the direction of jet. Find the force exerted on the plate in the direction of the jet, power and efficiency of the jet. Assume t 9. Ajet of water of 75 mm diameter strikes a curved vane at its center with a velocity of 20 m/se. The curved vane is moving with a velocity the plate to be smooth. Swer

8 m/sec in the direction of jet. Find the force exerted on the plate in the direction of the jet, power and efficiency of the jet. Assume t 9. Ajet of water of 75 mm diameter strikes a curved vane at its center with a velocity of 20 m/se. The curved vane is moving with a velocity the plate to be smooth. Swer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water enters vertically and steadily at a rate of 10 L/s into the sprinkler shown. Both water jets have a diameter of 1.2 cm. Disregarding any frictional effects, determine (a) the rotational speed of the sprinkler in rpm and (b) the torque required to prevent the sprinkler from rotating
A piston 46mm in diameter slides concentrically in a fixed cylinder 50mm in diameter. The cylinder is filled with water and when the piston moves into the annular gap, water flows through the annular gap surrounding the piston. If the velocity of piston is 75mm/s raletive to the cylinder, determine the velocity of flow through the gap.
In an experiment a jet of water of diameter 20 mm is fired vertically upwards at a sprung target thatdeflects the water at an angle of 120° to the horizontal in all directions. If a 500g mass placed on thetarget balances the force of the jet, what is the discharge of the jet in litre/s?
jet of water of diameter 100 mm strikes a curved plate at its center with a velocity of 15 m/s. The curved plate is moving with a velocity of 7 m/s in the direction of the jet. The jet is deflected through an angle of 150°. Assuming the plate smooth find: (i) Force exerted on the plate in the direction of the jet. (ii) Power of the jet, and (iii) Efficiency.
Find the force exerted by a jet of water of diameter 75 mm on a stationary flat plate, when the jet strikes the plate normally with velocity of 20 m/s.
The pressure gage leading to the turbine casing of a Francis turbine reads 0.5 MPa and the center of the spiral casing is 5 m above the tailrace. What is the net head if the velocity of the water entering the turbine is 10 m/s?
The jet of water of a pelton wheel is 80mm diameter. The jet strike's the bucket on the tangential line 0.45m from the centre of the wheel and the jet is deflected through 160° while it is moving across the bucket. Ignore friction and determine the power and hydraulic efficiency if the speed is 275 r/min and the pressure behind the nozzle is 680kPa
If a jet is inclined upward 30O from the horizontal, what must be itsvelocity to reach over a 3-m wall at a horizontal distance of 18 m,neglecting friction?
Water at 20°C, in the pressurized tank flows out and creates a vertical jet as shown. Assuming steady frectionless flow, determine the heaght H to which the jet rises.
A tank has one of its side inclined inward at an angle of 30 degrees with horizontal. The free surface of the contained water is at Elev 15.25 m. The orifice located on the inclined side issues a jet, having its vena contracta at Elev 10.70 m. If the highest point in the trajectory of the jet is at Elev. 14.00m, find the actual velocity of the jet. Neglect air friction. Include Illustration if needed. a.9.3 m/s b.8.3 m/s c.10.3 m/s d.11.3 m/s
6.36 This two-dimensional water (at 50°F) jet is deflected by the two-dimensional vane, which is moving to the right with a speed of 60 ft/s. The initial jet is 0.30 ft thick (vertical dimension), and its speed is 100 ft/s. What power per foot of the jet (normal to the page) is transmitted to the vane? See §6.5 for useful knowledge about moving CVs.
Water, issuing vertically from a nozzle having a diameter of 25 mm, flows out under a head of 30 m. If C = Cv = 0.98, determine at what constant height could the jet of water support a load of 200 N vertically from the nozzle tip?